- 您现在的位置：买卖IC网 > PDF目录79982 > LTC3521IFE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | LTC3521IFE#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-20 |
| 文件页数： | 6/22页 |
| 文件大小： | 1476K |
| 代理商： | LTC3521IFE#TRPBF |
LTC3521
14
3521fa
APPLICATIONS INFORMATION
The basic LTC3521 application circuit is shown as the
Typical Application on the front page of this data sheet.
The external component selection is determined by the
desired output voltages, output currents and ripple volt-
age requirements of each particular application. Basic
guidelines and considerations for the design process are
provided in this section.
Buck Inductor Selection
The choice of buck inductor value influences both the ef-
ficiency and the magnitude of the output voltage ripple.
Larger inductance values will reduce inductor current
ripple and lead to lower output voltage ripple. For a fixed
DC resistance, a larger value inductor will yield higher
efficiency by lowering the peak current closer to the av-
erage. However, a larger inductor within the same family
will generally have a greater series resistance, thereby
offsetting this efficiency advantage.
Givenadesiredpeak-to-peakcurrentripple,ΔIL,therequired
inductance can be calculated via the following expression,
where f represents the switching frequency in MHz:
L
=
1
f
IL
VOUT 1–
VOUT
VIN
H
( )
A reasonable choice for ripple current is ΔIL = 240mA
which represents 40% of the maximum 600mA load
current. The DC current rating of the inductor should be
at least equal to the maximum load current, plus half the
ripple current, in order to prevent core saturation and loss
of efficiency during operation. To optimize efficiency, the
inductor should have a low series resistance.
In particularly space-restricted applications, it may be
advantageous to use a much smaller value inductor at
the expense of larger ripple current. In such cases, the
converter will operate in discontinuous conduction for a
wider range of output loads and efficiency will be reduced.
In addition, there is a minimum inductor value required
to maintain stability of the current loop (given the fixed
internal slope compensation). Specifically, if the buck
converter is going to be utilized at duty cycles over 40%,
the inductance value must be at least LMIN, as given by
the following equation:
LMIN = 2.5 VOUT (H)
Table 1 depicts the recommended inductance for several
common output voltages.
Table 1. Buck Recommended Inductance
OUTPUT VOLTAGE
MINIMUM
INDUCTANCE
MAXIMUM
INDUCTANCE
0.6V
1.5μH
2.2μH
1.2V
2.2μH
4.7μH
1.8V
3.3μH
6.8μH
2.5V
4.7μH
8.2μH
Buck Output Capacitor Selection
A low ESR output capacitor should be utilized at the buck
output in order to minimize voltage ripple. Multilayer ce-
ramic capacitors are an excellent choice as they have low
ESR and are available in small footprints. In addition to
controlling the ripple magnitude, the value of the output
capacitor also sets the loop crossover frequency and can,
therefore, impact loop stability. There is both a minimum
andmaximumcapacitancevaluerequiredtoensurestabil-
ity of the loop. If the output capacitance is too small, the
loop crossover frequency will increase to the point where
the switching delay and the high frequency parasitic poles
of the error amplifier will degrade the phase margin. In
addition, the wider bandwidth produced by a small output
capacitor will make the loop more susceptible to switch-
ing noise. At the other extreme, if the output capacitor
is too large, the crossover frequency can decrease too
far below the compensation zero and lead to a degraded
phase margin. Table 2 provides a guideline for the range
of allowable values of low ESR output capacitors. Larger
value output capacitors can be accommodated provided
they have sufficient ESR to stabilize the loop.
Table 2. Buck Output Capacitor Range
VOUT
CMIN
CMAX
0.6V
15μF
300μF
0.8V
15μF
230μF
1.2V
10μF
150μF
1.8V
10μF
90μF
2.7V
10μF
70μF
3.3V
6.8μF
50μF
相关PDF资料 |
PDF描述 |
|---|---|
| LS4501-9PD6TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LK2320-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LK2540-7EPD2TB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7EPD7T | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1301-9ERD1TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3521IUF#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3521IUF#TRPBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3522 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters |
| LTC3522EUD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous 400mA Buck-Boost and 200mA Buck Converters |
| LTC3522EUD#PBF | 功能描述:IC REG BUCK BOOST SYNC ADJ 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
发布紧急采购，3分钟左右您将得到回复。