- 您现在的位置：买卖IC网 > PDF目录13970 > LTC3536IMSE#PBF (Linear Technology)IC REG BUCK BST SYNC ADJ 12MSOP PDF资料下载
参数资料
| 型号： | LTC3536IMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK BST SYNC ADJ 12MSOP |
| 标准包装： | 37 |
| 类型： | 降压（降压），升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.8 V ~ 5.5 V |
| 输入电压： | 1.8 V ~ 5.5 V |
| PWM 型： | 电压模式，混合 |
| 频率 - 开关： | 300kHz ~ 2MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TSSOP （0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 12-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3536
PIN FUNCTIONS
(DFN/MSOP)
RT (Pin 1/Pin 1): Oscillator Frequency Programming
Input. Connect a resistor from RT to GND to program the
internal oscillator frequency. The frequency is given by:
f OSC (MHz) = 100/R T (kΩ)
where R T is in kΩ and f OSC is between 0.3MHz and 2MHz.
Tying the RT pin to V IN enables the internal 1.2MHz default
oscillator frequency.
SGND (Pin 2/Pin 2): Ground Connection for the LTC3536.
A ground plane is highly recommended. Sensitive analog
components terminated at ground should connect to the
GND pin with a Kelvin connection, separated from the
high current path.
MODE/SYNC (Pin 3/Pin 3): Pulse Width Modulation/Burst
Mode Selection and Synchronization Input. Driving MODE
to a logic 0 state programs fixed frequency, low noise
PWM operation. Driving MODE to logic 1 state programs
Burst Mode operation for highest efficiency at light loads.
In Burst Mode operation, the output current capability is
significantly less than what is available in PWM operation.
Refer to the Applications Information section of this data
sheet for details. Frequency synchronization is achieved
if a clock pulse is applied to MODE/SYNC. The external
clock pulse amplitude must have an amplitude equal or
higher than 1.2V and duty cycle from 10% and 90%. The
free-running frequency of the LTC3536 oscillator can be
programmed slower or faster than the synchronization
clock frequency.
SW1 (Pin 4/Pin 4): Switch Pin. Connect to internal power
switches A and B. Connect one side of the buck-boost
inductor to SW1. Provide a short wide PCB trace from the
inductor to SW1 to minimize voltage transients and noise.
SW2 (Pin 5/Pin 6): Switch Pin. Connect to internal power
switches C and D. Connect one side of the buck-boost
inductor to SW2. Provide a short wide PCB trace from the
inductor to SW2 to minimize voltage transients and noise.
V OUT (Pin 6/Pin 7): Output Voltage. This pin is the power
output for the regulator. A low ESR capacitor should be
placed between this pin and the ground plane. The capaci-
tor should be placed as close to this pin as possible and
have a short return path to ground.
V IN (Pin 7/Pins 8, 9): Power Input for the Converter. A low
ESR 10μF or larger bypass capacitor should be connected
between this pin and ground. The capacitor should be
placed as close to this pin as possible and have a short
return path to ground.
SHDN (Pin 8/Pin 10): Enable Input. A logic 1 on SHDN
activates the buck-boost regulator. A logic 0 on SHDN
deactivates the buck-boost regulator.
FB (Pin 9/Pin 11): Output Voltage Programming Feedback
Divider Input. The regulator output voltage is programmed
by the voltage divider connected to FB. The buck-boost
output is given by the following equation:
V OUT = 0.6V ? (1 + R TOP /R BOT ) (V)
where R BOT is a resistor connected between FB and ground
and R TOP is a resistor connected between FB and V OUT .
The buck-boost output voltage can be adjusted from 1.8V
to 5.5V.
VC (Pin 10/Pin 12): Error Amplifier Output. Frequency
compensation components are connected between VC
and FB to provide stable operation of the converter. Refer
to the Applications Information section of this data sheet
for design details.
PGND (Exposed Pad Pin 11/Pin 5, Exposed Pad Pin?13):
Power Ground. The exposed pad must be soldered to the
PCB and electrically connected to ground through the
shortest and lowest impedance connection possible.
3536fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3521EUF#PBF | IC REG BUCK BOOST SYNC ADJ 24QFN |
| LT3695EMSE-3.3#PBF | IC REG BUCK 3.3V 1A 16MSOP |
| V110B15C150B2 | CONVERTER MOD DC/DC 15V 150W |
| V110B12E200BG2 | CONVERTER MOD DC/DC 12V 200W |
| V110B12E200BG | CONVERTER MOD DC/DC 12V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3537 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
| LTC3537EUD#PBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC3537EUD#TRPBF | 功能描述:IC REG DL BST/LINEAR SYNC 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LTC3537EUD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
| LTC3537EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.2 MHz, 600mA Synchronous Step-Up DC/DC Converter and 100mA LDO |
发布紧急采购，3分钟左右您将得到回复。