参数资料
型号: LTC3542ES6#TRPBF
厂商: Linear Technology
文件页数: 7/16页
文件大小: 0K
描述: IC REG BUCK SYNC ADJ TSOT23-6
标准包装: 2,500
类型: 降压(降压)
输出类型: 可调式
输出数: 1
输出电压: 0.6 V ~ 5.5 V
输入电压: 2.5 V ~ 5.5 V
PWM 型: 电流模式,混合
频率 - 开关: 2.25MHz
电流 - 输出: 500mA
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: SOT-23-6 细型,TSOT-23-6
包装: 带卷 (TR)
供应商设备封装: TSOT-23-6
LTC3542
OPERATION
The LTC3542 uses a constant frequency, current mode,
step-down architecture. The operating frequency is set at
2.25MHz and can be synchronized to an external oscillator.
To suit a variety of applications, the selectable MODE/SYNC
pin allows the user to trade-off noise for ef?ciency.
The output voltage is set by an external divider returned
to the V FB pin. An error ampli?er compares the divided
output voltage with a reference voltage of 0.6V and adjusts
the peak inductor current accordingly.
Main Control Loop
During normal operation, the top power switch (P-channel
MOSFET) is turned on at the beginning of a clock cycle
when the V FB voltage is below the reference voltage. The
current ?ows into the inductor and the load increases until
the current limit is reached. The switch turns off and energy
stored in the inductor ?ows through the bottom switch
(N-channel MOSFET) into the load until the next clock cycle.
The peak inductor current is controlled by the internally
compensated output of the error ampli?er. When the load
current increases, the V FB voltage decreases slightly below
the reference. This decrease causes the error ampli?er to
increase its output voltage until the average inductor cur-
rent matches the new load current. The main control loop
is shut down by pulling the RUN pin to ground.
Low Load Current Operation
By selecting MODE/SYNC pin, two modes are available to
control the operation of the LTC3542 at low load currents.
Both modes automatically switch from continuous opera-
tion to the selected mode when the load current is low.
To optimize ef?ciency, the Burst Mode operation can be
selected. When the converter is in Burst Mode operation,
the peak current of the inductor is set to approximately
60mA regardless of the output load. Each burst event can
last from a few cycles at light loads to almost continuously
cycling with short sleep intervals at moderate loads. In
between these burst events, the power MOSFETs and any
unneeded circuitry are turned off, reducing the quiescent
current to 26μA. In this sleep state, the load current is
being supplied solely from the output capacitor. As the
the sleep threshold and turns the top MOSFET on. This
process repeats at a rate that is dependent on the load
demand. By running cycles periodically, the switching
losses which are dominated by the gate charge losses of
the power MOSFETs are minimized.
For lower ripple noise at low load currents, the pulse skip
mode can be used. In this mode, the regulator continues
to switch at a constant frequency down to very low load
currents, where it will begin skipping pulses.
Dropout Operation
When the input supply voltage decreases toward the output
voltage, the duty cycle increases to 100%, which is the
dropout condition. In dropout, the PMOS switch is turned
on continuously with the output voltage being equal to the
input voltage minus the voltage drops across the internal
P-channel MOSFET and the inductor. An important design
consideration is that the R DS(ON) of the P-channel switch
increases with decreasing input supply voltage (See Typical
Performance Characteristics). Therefore, the user should
calculate the power dissipation when the LTC3542 is used
at 100% duty cycle with low input voltage (See Thermal
Considerations in the Applications Information Section).
Low Supply Operation
To prevent unstable operation, the LTC3542 incorporates
an undervoltage lockout circuit which shuts down the part
when the input voltage drops below about 2V.
Internal Soft-Start
At start-up when the RUN pin is brought high, the internal
reference is linearly ramped from 0V to 0.6V in about 1ms.
The regulated feedback voltage follows this ramp resulting
in the output voltage ramping from 0% to 100% in 1ms.
The current in the inductor during soft-start is de?ned
by the combination of the current needed to charge the
output capacitance and the current provided to the load
as the output voltage ramps up. The start-up waveform,
shown in the Typical Performance Characteristics, shows
the output voltage start-up from 0V to 1.8V with a 500mA
load and V IN = 3.6V (refer to Figure 3a).
output voltage drops, the EA ampli?er’s output rises above
3542fa
7
相关PDF资料
PDF描述
HM79-50181LFTR13 INDUCTOR 180UH MEDIUM PWR SMD
MLP221M350EA0A CAP ALUM 220UF 350V 20% RADIAL
MLP201M420EA0A CAP ALUM 200UF 420V 20% RADIAL
HM79-50151LFTR13 INDUCTOR 150UH MEDIUM PWR SMD
HM79-50121LFTR13 INDUCTOR 120UH MEDIUM PWR SMD
相关代理商/技术参数
参数描述
LTC3542IDC#TRMPBF 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压(升压) 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式,混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC(0.154",3.90mm 宽) 包装:带卷 (TR) 供应商设备封装:8-SOIC
LTC3542IDC#TRPBF 功能描述:IC REG BUCK SYNC ADJ 0.5A 6DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压(升压) 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式,混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC(0.154",3.90mm 宽) 包装:带卷 (TR) 供应商设备封装:8-SOIC
LTC3542IDC-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA, 2.25MHz Synchronous Step-Down DC/DC Converter
LTC3542IDC-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA, 2.25MHz Synchronous Step-Down DC/DC Converter
LTC3542IS6#PBF 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.5V to 5.5V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, Cut Tape 500mA, 2.25MHz Synchronous Step-Down DC/DC Convert