- 您现在的位置：买卖IC网 > PDF目录14133 > LTC3543EDCB#TRMPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 8DFN PDF资料下载
参数资料
| 型号： | LTC3543EDCB#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 8DFN |
| 标准包装： | 500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN（3x2） |
LTC3543
APPLICATIONS INFORMATION
1. The V IN quiescent current is due to two components: the
DC bias current as given in the Electrical Characteristics
and the internal main switch and synchronous switch
gate charge currents. The gate charge current results
from switching the gate capacitance of the internal power
MOSFET switches. Each time the gate is switched from
high to low to high again, a packet of charge, dQ, moves
from V IN to ground. The resulting dQ/dt is the current out
of V IN that is typically larger than the DC bias current. In
continuous mode, I GATECHG = f(QT + QB) where QT and
QB are the gate charges of the internal top and bottom
switches. Both the DC bias and gate charge losses are
proportional to V IN and thus their effects will be more
pronounced at higher supply voltages.
2. I 2 R losses are calculated from the resistances of the
internal switches, R SW , and external inductor RL. In
continuous mode, the average output current ?owing
through inductor L is “chopped” between the main
switch and the synchronous switch. Thus, the series
resistance looking into the SW pin is a function of both
top and bottom MOSFET R DS(ON) and the duty cycle
(DC) as follows:
R SW = (R DS(ON)TOP ? DC) + (R DS(ON)BOT ? (1 – DC))
The R DS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Characteristics
curves. Thus, to obtain I 2 R losses, simply add R SW to
RL and multiply the result by the square of the average
output current.
Other losses, including C IN and C OUT ESR dissipative losses
and inductor core losses, generally account for less than
2% total additional loss.
Thermal Considerations
In most applications, the LTC3543 does not dissipate much
heat due to its high ef?ciency. But, in applications where the
LTC3543 is running at high ambient temperature with low
supply voltage and high duty cycles, such as in dropout,
the heat dissipated may exceed the maximum junction
temperature of the part. If the junction temperature reaches
approximately 150°C, both power switches will be turned
off and the SW node will become high impedance.
To avoid the LTC3543 from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum
junction temperature of the part. The temperature rise is
given by:
T R = θ JA ? P D
where P D is the power dissipated by the regulator and
θ JA is the thermal resistance from the junction of the die
to the temperature.
The junction temperature, T J , is given by:
T J = T A + T R
where T A is the ambient temperature.
As an example, consider the LTC3543 in dropout at an
input voltage of 2.7V, an ambient temperature of 80°C, and
a load current of 600mA. From the typical performance
graph of switch resistance, the R DS(ON) of the P-channel
switch at 80°C is approximately 0.41 Ω . There, power
dissipated by the part is:
P D = I LOAD2 ? R DS(ON) = 147.6mW
For the DFN package, the θ JA is 64°C/W. Thus, the junction
temperature of the regulator is:
T J = 80°C + 0.1476 ? 64 = 89.4°C
which is well below the maximum junction temperature of
125°C. Note that at higher supply voltages, the junction
temperature is lower due to reduced switch resistance
(R DS(ON) ).
3543fa
14
相关PDF资料 |
PDF描述 |
|---|---|
| HM66A-0630120NLF13 | SHIELDED POWER INDUCTORS |
| VI-J42-CZ-F1 | CONVERTER MOD DC/DC 15V 25W |
| HM66A-0630100NLF13 | SHIELDED POWER INDUCTORS |
| LTC3531EDD-3#PBF | IC REG BUCK BST SYNC 3V .2A 8DFN |
| HM66A-06308R0NLF13 | SHIELDED POWER INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3544 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad Synchronous Step-Down Regulator: 2.25MHz, 300mA, 200mA, 200mA, 100mA |
| LTC3544B | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad Synchronous Step-Down Regulator: 2.25MHz, 300mA, 200mA, 200mA, 100mA |
| LTC3544BEUD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad Synchronous Step-Down Regulator: 2.25MHz, 300mA, 200mA, 200mA, 100mA |
| LTC3544BEUD#PBF | 功能描述:IC REG BUCK SYNC ADJ QUAD 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3544BEUD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ QUAD 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。