- 您现在的位置：买卖IC网 > PDF目录13917 > LTC3546EUFD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 1A/2A 28QFN PDF资料下载
参数资料
| 型号： | LTC3546EUFD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1A/2A 28QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz，750kHz ~ 4MHz |
| 电流 - 输出： | 1A，2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 28-QFN（4x5） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3546
APPLICATIONS INFORMATION
C OUT ≈ 2.5
V OUT1 ≈ 0.6V ? 1 +
? R1 ?
?
R2 ?
V OUT2 ≈ 0.6V ? 1 +
? R3 ?
?
R4 ?
density, but it has a larger ESR and it is critical that the
capacitors are surge tested for use in switching power
supplies. An excellent choice is the AVX TPS series of
surface tantalums, available in case heights ranging from
2mm to 4mm. Aluminum electrolytic capacitors have a
significantly larger ESR, and are often used in extremely
cost-sensitive applications provided that consideration
is given to ripple current ratings and long term reliability.
Ceramic capacitors have the lowest ESR and cost but also
have the lowest capacitance density, high voltage and
temperature coefficient and exhibit audible piezoelectric
effects. In addition, the high Q of ceramic capacitors along
with trace inductance can lead to significant ringing. Other
capacitor types include the Panasonic specialty polymer
(SP) capacitors.
Ceramic Input and Output Capacitors
Higher value, lower cost ceramic capacitors are now
becoming available in smaller case sizes. Because the
LTC3546 control loop does not depend on the output
capacitor’s ESR for stable operation, ceramic capacitors
can be used freely to achieve very low output ripple and
small circuit size. When choosing the input and output
ceramic capacitors, choose the X5R or X7R dielectric
formulations. These dielectrics have the best temperature
and voltage characteristics of all the ceramics for a given
value and size.
Great care must be taken when using only ceramic input
and output capacitors. When a ceramic capacitor is used
at the input and the power is being supplied through long
wires, such as from a wall adapter, a load step at the output
can induce ringing at the V IN pin. At best, this ringing can
couple to the output and be mistaken as loop instability.
At worst, the ringing at the input can be large enough to
disrupt circuit operation or damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement. During a load step, the output capacitor must
instantaneously supply the current to support the load
until the feedback loop raises the switch current enough
to support the load. The time required for the feedback
loop to respond is dependent on the compensation com-
ponents and the output capacitor size. Typically, 3 to 4
cycles are required to respond to a load step, but only in
the first cycle does the output drop linearly. The output
droop, V DROOP , is usually about 2 to 3 times the linear
droop of the first cycle. Thus, a good place to start is with
the output capacitor size of approximately:
Δ I OUT
f O V DROOP
More capacitance may be required depending on the duty
cycle and load step requirements.
In most applications, the input capacitor is merely required
to supply high frequency bypassing, since impedance to
the supply is very low. A 10μF ceramic capacitor is usually
enough for these conditions.
Setting the Output Voltage
The LTC3546 generates a 0.6V reference voltage between
the feedback pin, V FB1 and V FB2 , and the signal ground.
The output voltage is set by a resistive divider according
to the following formula:
?
?
Resistor locations are shown in Figure 2.
V OUT1 V OUT2
C FF1 R1 R3 C FF2
LTC3546
V FB1 V FB2
R2 3546 F02 R4
Figure 2. Setting Output Voltages
17
For more information www.linear.com/3546
3546fc
相关PDF资料 |
PDF描述 |
|---|---|
| RGM10DTAH | CONN EDGECARD 20POS R/A .156 SLD |
| LTC1434IGN#PBF | IC REG BUCK 3.3V/5V/ADJ 20SSOP |
| MAX6724AUTWED6+T | IC SUPERVISOR MPU SOT23-6 |
| LTC1434IGN | IC REG BUCK 3.3V/5V/ADJ 20SSOP |
| USA1HR47MDD | CAP ALUM 0.47UF 50V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3546IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IUFD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A/2A 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
发布紧急采购，3分钟左右您将得到回复。