- 您现在的位置：买卖IC网 > PDF目录16307 > LTC3559EUD#PBF (Linear Technology)IC USB CHARGER 16-QFN PDF资料下载
参数资料
| 型号： | LTC3559EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/24页 |
| 文件大小： | 0K |
| 描述： | IC USB CHARGER 16-QFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC3559/LTC3559-1
APPLICATIONS INFORMATION
Suspend Mode
The battery charger can also be disabled by pulling the
SUSP pin above 1.2V. In suspend mode, the battery
drain current is reduced to 1.5μA and the input current is
reduced to 8.5μA.
Charge Cycle Overview
When a battery charge cycle begins, the battery charger
?rst determines if the battery is deeply discharged. If the
battery voltage is below V TRKL , typically 2.9V, an automatic
trickle charge feature sets the battery charge current to
10% of the full-scale value.
Once the battery voltage is above 2.9V, the battery charger
begins charging in constant-current mode. When the
battery voltage approaches the 4.2V (LTC3559) or 4.1V
(LTC3559-1) required to maintain a full charge, otherwise
known as the ?oat voltage, the charge current begins to
decrease as the battery charger switches into constant-
voltage mode.
Trickle Charge and Defective Battery Detection
Any time the battery voltage is below V TRKL , the charger
goes into trickle charge mode and reduces the charge
current to 10% of the full-scale current. If the battery
voltage remains below V TRKL for more than 1/2 hour, the
charger latches the bad-battery state, automatically termi-
nates, and indicates via the CHRG pin that the battery was
unresponsive. If for any reason the battery voltage rises
above V TRKL , the charger will resume charging. Since the
charger has latched the bad-battery state, if the battery
voltage then falls below V TRKL again but without rising past
V RECHRG ?rst, the charger will immediately assume that
the battery is defective. To reset the charger (i.e., when
the dead battery is replaced with a new battery), simply
remove the input voltage and reapply it or put the part in
mode, the 4-hour timer is started. After the safety timer
expires, charging of the battery will discontinue and no
more current will be delivered.
Automatic Recharge
After the battery charger terminates, it will remain off,
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that the
battery is always topped off, a charge cycle will automati-
cally begin when the battery voltage falls below V RECHRG . In
the event that the safety timer is running when the battery
voltage falls below V RECHRG , it will reset back to zero. To
prevent brief excursions below V RECHRG from resetting the
safety timer, the battery voltage must be below V RECHRG
for more than 1.7ms. The charge cycle and safety timer
will also restart if the V CC UVLO or DUVLO cycles low and
then high (e.g., V CC is removed and then replaced) or the
charger enters and then exits suspend mode.
Programming Charge Current
The PROG pin serves both as a charge current program
pin, and as a charge current monitor pin. By design, the
PROG pin current is 1/800th of the battery charge current.
Therefore, connecting a resistor from PROG to ground
programs the charge current while measuring the PROG pin
voltage allows the user to calculate the charge current.
Full-scale charge current is de?ned as 100% of the con-
stant-current mode charge current programmed by the
PROG resistor. In constant-current mode, the PROG pin
servos to 1V if HPWR is high, which corresponds to charg-
ing at the full-scale charge current, or 200mV if HPWR
is low, which corresponds to charging at 20% of the full-
scale charge current. Thus, the full-scale charge current
and desired program resistor for a given full-scale charge
current are calculated using the following equations:
and out of suspend mode.
Charge Termination
I CHG =
800 V
R PROG
Thebatterychargerhasabuilt-insafetytimerthatsetsthe
total charge time for 4 hours. Once the battery voltage rises
above V RECHRG and the charger enters constant-voltage
R PROG =
800 V
I CHG
3559fb
12
相关PDF资料 |
PDF描述 |
|---|---|
| CM453232-3R9KL | INDUCTOR CHIP 3.9UH 10% 1812 SMD |
| VE-J1N-EZ-F4 | CONVERTER MOD DC/DC 18.5V 25W |
| CM453232-2R7KL | INDUCTOR CHIP 2.7UH 10% 1812 SMD |
| CM453232-1R8KL | INDUCTOR CHIP 1.8UH 10% 1812 SMD |
| CM453232-1R2KL | INDUCTOR CHIP 1.2UH 10% 1812 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3559EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Linear USB Battery Charger with Dual Buck Regulators |
| LTC3560 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560E | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560ES6 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560ES6#PBF | 制造商:Linear Technology 功能描述:2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
发布紧急采购，3分钟左右您将得到回复。