- 您现在的位置：买卖IC网 > PDF目录16307 > LTC3559EUD#PBF (Linear Technology)IC USB CHARGER 16-QFN PDF资料下载
参数资料
| 型号： | LTC3559EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC USB CHARGER 16-QFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC3559/LTC3559-1
APPLICATIONS INFORMATION
most applications. Experimentation with capacitor sizes
between 2pF and 22pF may yield improved transient
response if so desired by the user.
Buck Switching Regulator Operating Modes
The step-down switching regulators include two possible
operating modes to meet the noise/power needs of a
variety of applications.
In pulse skip mode, an internal latch is set at the start of
every cycle, which turns on the main P-channel MOSFET
switch. During each cycle, a current comparator compares
the peak inductor current to the output of an error ampli?er.
The output of the current comparator resets the internal
latch, which causes the main P-channel MOSFET switch to
turn off and the N-channel MOSFET synchronous recti?er
to turn on. The N-channel MOSFET synchronous recti?er
turns off at the end of the 2.25MHz cycle or if the current
through the N-channel MOSFET synchronous recti?er
drops to zero. Using this method of operation, the error
ampli?er adjusts the peak inductor current to deliver the
required output power. All necessary compensation is
internal to the step-down switching regulator requiring
only a single ceramic output capacitor for stability. At
light loads in pulse skip mode, the inductor current may
reach zero on each pulse which will turn off the N-channel
MOSFET synchronous recti?er. In this case, the switch
node (SW1 or SW2) goes high impedance and the switch
node voltage will “ring”. This is discontinuous operation,
and is normal behavior for a switching regulator. At very
light loads in pulse skip mode, the step-down switching
P VIN
regulators will automatically skip pulses as needed to
maintain output regulation. At high duty cycle (V OUT >
PV IN /2) in pulse skip mode, it is possible for the inductor
current to reverse causing the buck converter to switch
continuously. Regulation and low noise operation are
maintained but the input supply current will increase to a
couple mA due to the continuous gate switching.
During Burst Mode operation, the step-down switching
regulators automatically switch between ?xed frequency
PWM operation and hysteretic control as a function of
the load current. At light loads the step-down switching
regulators control the inductor current directly and use a
hysteretic control loop to minimize both noise and switching
losses. During Burst Mode operation, the output capacitor
is charged to a voltage slightly higher than the regulation
point. The step-down switching regulator then goes into
sleep mode, during which the output capacitor provides
the load current. In sleep mode, most of the switching
regulator’s circuitry is powered down, helping conserve
battery power. When the output voltage drops below a
pre-determined value, the step-down switching regulator
circuitry is powered on and another burst cycle begins. The
sleep time decreases as the load current increases. Beyond
a certain load current point (about 1/4 rated output load
current) the step-down switching regulators will switch to
a low noise constant frequency PWM mode of operation,
much the same as pulse skip operation at high loads. For
applications that can tolerate some output ripple at low
output currents, Burst Mode operation provides better
ef?ciency than pulse skip at light loads.
The step-down switching regulators allow mode transition
on-the-?y, providing seamless transition between modes
EN
MODE
PWM
CONTROL
MP
SW
MN
L
C FB
V OUT
+
R1
C O
even under load. This allows the user to switch back and
forth between modes to reduce output ripple or increase
low current ef?ciency as needed. Burst Mode operation is
set by driving the MODE pin high, while pulse skip mode
is achieved by driving the MODE pin low.
FB
Buck Switching Regulator in Shutdown
GND
0.8V
R2
3559 F08
The buck switching regulators are in shutdown when
not enabled for operation. In shutdown, all circuitry in
the buck switching regulator is disconnected from the
regulator input supply, leaving only a few nanoamps of
Figure 8. Buck Converter Application Circuit
3559fb
19
相关PDF资料 |
PDF描述 |
|---|---|
| CM453232-3R9KL | INDUCTOR CHIP 3.9UH 10% 1812 SMD |
| VE-J1N-EZ-F4 | CONVERTER MOD DC/DC 18.5V 25W |
| CM453232-2R7KL | INDUCTOR CHIP 2.7UH 10% 1812 SMD |
| CM453232-1R8KL | INDUCTOR CHIP 1.8UH 10% 1812 SMD |
| CM453232-1R2KL | INDUCTOR CHIP 1.2UH 10% 1812 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3559EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Linear USB Battery Charger with Dual Buck Regulators |
| LTC3560 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560E | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560ES6 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2.25MHz, 800mA Synchronous Step-Down Regulator in ThinSOT |
| LTC3560ES6#PBF | 制造商:Linear Technology 功能描述:2.1 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
发布紧急采购，3分钟左右您将得到回复。