- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3560IS6#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ TSOT23-6 PDF资料下载
参数资料
| 型号： | LTC3560IS6#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ TSOT23-6 |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | TSOT-23-6 |
LTC3560
OPERATION
Main Control Loop
(Refer to Functional Diagram)
When the converter is in Burst Mode operation, the peak
The LTC3560 uses a constant frequency, current mode step-
down architecture. Both the main (P-channel MOSFET)
and synchronous (N-channel MOSFET) switches are
internal. During normal operation, the internal top power
MOSFET is turned on each cycle when the oscillator sets
the RS latch, and turned off when the current comparator,
I COMP , resets the RS latch. The peak inductor current
at which I COMP resets the RS latch, is controlled by the
output of error ampli?er EA. The V FB pin, described in
the Pin Functions section, allows EA to receive an output
feedback voltage from an external resistive divider. When
the load current increases, it causes a slight decrease in
the feedback voltage relative to the 0.6V reference, which
in turn, causes the EA ampli?er’s output voltage to increase
until the average inductor current matches the new load
current. While the top MOSFET is off, the bottom MOSFET
is turned on until either the inductor current starts to
reverse, as indicated by the current reversal comparator
I RCMP , or the beginning of the next clock cycle.
The main control loop is shut down by grounding RUN,
resetting the internal soft-start. Re-enabling the main
control loop by pulling RUN high activates the internal
soft-start, which slowly ramps the output voltage over
approximately 0.9ms until it reaches regulation.
Burst Mode Operation
The LTC3560 is capable of Burst Mode operation in which
the internal power MOSFETs operate intermittently based
on load demand. To enable Burst Mode operation, simply
connect the SYNC/MODE pin to GND. To disable Burst
Mode operation and enable PWM pulse-skipping mode,
connect the SYNC/MODE pin to V IN or drive it with a logic
high (V MODE > 1.5V). In this mode, the ef?ciency is lower
at light loads, but becomes comparable to Burst Mode
operation when the output load exceeds 100mA. The
advantage of pulse-skipping mode is lower output ripple
and less interference to audio circuitry.
current of the inductor is set to approximately 150mA
regardless of the output load. Each burst event can last
from a few cycles at light loads to almost continuously
cycling with short sleep intervals at moderate loads. In
between these burst events, the power MOSFETs and any
unneeded circuitry are turned off, reducing the quiescent
current to 16μA. In this sleep state, the load current is being
supplied solely from the output capacitor. As the output
voltage droops, the EA ampli?er’s output rises above the
sleep threshold signaling the BURST comparator to trip
and turn the top MOSFET on. This process repeats at a
rate that is dependent on the load demand.
Frequency Synchronization
When the LTC3560 is clocked by an external source, Burst
Mode operation is disabled; the LTC3560 then operates in
PWM pulse-skipping mode. In this mode, when the output
load is very low, current comparator I COMP may remain
tripped for several cycles and force the main switch to stay
off for the same number of cycles. Increasing the output
load slightly allows constant frequency PWM operation
to resume. This mode exhibits low output ripple as well
as low audio noise and reduced RF interference while
providing reasonable low current ef?ciency.
Dropout Operation
As the input supply voltage decreases to a value approaching
the output voltage, the duty cycle increases toward the
maximum on time. Further reduction of the supply voltage
forces the main switch to remain on for more than one cycle
until it reaches 100% duty cycle. The output voltage will
then be determined by the input voltage minus the voltage
drop across the P-channel MOSFET and the inductor.
Another important detail to remember is that at low input
supply voltages, the R DS(ON) of the P-channel switch
increases (see Typical Performance Characteristics).
Therefore, the user should calculate the power dissipation
when the LTC3560 is used at 100% duty cycle with low
input voltage (See Thermal Considerations in the Applica-
tions Information section).
3560fb
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3561EDD#TRPBF | IC REG BUCK SYNC ADJ 1A 8DFN |
| LTC3562EUD#TRPBF | IC REG BUCK SYNC ADJ QUAD 20QFN |
| LTC3563EDC#TRPBF | IC REG BUCK SYNC 0.5A 6DFN |
| LTC3564IS5#TRPBF | IC REG BUCK SYNC ADJ TSOT23-5 |
| LTC3565IMSE#TRPBF | IC REG BUCK SYNC ADJ 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3561 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3561A | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
| LTC3561AEDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3561AEDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3561AEDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:1A, 4MHz, Synchronous Step-Down DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。