- 您现在的位置：买卖IC网 > PDF目录13970 > LTC3569EFE#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 16TSSOP PDF资料下载
参数资料
| 型号： | LTC3569EFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 16TSSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 3 |
| 输出电压： | 0.43 V ~ 5.5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz，1MHz ~ 3MHz |
| 电流 - 输出： | 600mA，1.2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-TSSOP-EP |
LTC3569
APPLICATIONS INFORMATION
The second consideration is stray capacitance on the FB
pin traces and the R T pin trace to GND. This is taken into
account by cutting the ground plane beneath these traces.
However, wherever the ground plane is cut, add additional
decoupling capacitors across the break to provide a path
for high-frequency ground return currents to flow.
Finally, the third consideration is stray impedance between
the SW node and the inductor when operating with a slave
power stage. It is important to keep the stray inductance of
the slave power device to a minimum, by keeping the trace
from slave SW to the main SW as short as possible. This
requirement is necessary to ensure that the slave power
device’s share of the inductor current does not exceed that
of the master as well as to keep the current density in the
slave device under control. The inductor should be placed
close to the master SW pin to minimize stray impedance
and allow the master to control the inductor current.
Thermal Considerations
In the majority of applications, the LTC3569 does not dis-
sipate much heat due to its high efficiency. However, in
applications where the LTC3569 is running at high ambient
temperature with low supply voltage and high duty cycles,
such as in dropout, the heat dissipated may exceed the
maximum junction temperature of the part. If the junction
temperature reaches approximately 150°C, the LTC3569
will be turned off and 2k resistive pull-downs are tied to
all the SW nodes.
To prevent the LTC3569 from exceeding maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum junc-
tion temperature of the part. Temperature rise is:
t RISE = P D ? θ JA
Where P D is the power dissipated by the regulator and
θ JA is the thermal resistance from the junction of the die
to the ambient temperature.
The junction temperature, T J , is given by:
T J = t RISE + T A .
Where T A is the ambient temperature.
As an example, consider the case when the LTC3569 is
in dropout at an input voltage of 2.7V with load currents
of 1000mA, 500mA and 500mA for bucks 1, 2 and 3
respectively, at an ambient temperature of 85°C. From
the Typical Performance Characteristics, the R DS(ON) of
buck1 is 0.190?, and for buck2 and buck3 it is 0.265?.
Therefore, power dissipated by the LTC3569 is:
P D = I 12 R DS(ON)1 + I 22 R DS(ON)2 + I 32 R DS(ON)3
= 190mV + 66.25mW + 66.25mV
= 322.5mW
At 85°C ambient the junction temperature is:
T J = 322.5mW ?68°C/W + 85°C = 106.9°C.
This junction temperature is below the absolute maximum
junction temperature of 125°C.
Design Example 1: 2.5V, 1.8V and 1.2V From a
Li-Ion Battery
As a design example, consider using the LTC3569 in a
portable application with a Li-Ion battery source. The bat-
tery provides an SV IN from 2.9V to 4.2V. The loads require
2.5V, 1.8V and 1.2V with current requirements of up to
800mA, 400mA and 400mA respectively when active. The
first load, with the 2.5V rail has no standby requirements,
however loads 2 and 3 each require a current of 1mA in
standby. Since two of the loads require low current opera-
tion, Burst Mode operation is selected. With V IN(MAX) at
4.2V and V OUT(MIN) = 1.2V, the maximum clock frequency
is 3.57MHz based on minimum on-time requirements.
To simplify the board layout, the fixed 2.25MHz internal
frequency is selected.
3569fd
17
相关PDF资料 |
PDF描述 |
|---|---|
| AIAP-03-682-K | INDUCTOR 6800UH 10% .322A |
| RBM43DRYN | CONN EDGECARD 86POS DIP .156 SLD |
| AIAP-03-8R2-K | INDUCTOR 8.2UH 10% 9.89A |
| RBM43DRYH | CONN EDGECARD 86POS DIP .156 SLD |
| AIAP-03-472-K | INDUCTOR 4700UH 10% .39A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3569EUD#PBF | 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3569EUD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3569EUDC#PBF | 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3569EUDC#TRPBF | 功能描述:IC REG BUCK SYNC ADJ TRPL 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3569EUD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Triple Buck Regulator With 1.2A and Two 600mA Outputs and Individual Programmable References |
发布紧急采购，3分钟左右您将得到回复。