- 您现在的位置：买卖IC网 > PDF目录30770 > LTC3589IUJ-1#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 PDF资料下载
参数资料
| 型号： | LTC3589IUJ-1#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封装： | 6 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 15/46页 |
| 文件大小： | 570K |
| 代理商： | LTC3589IUJ-1#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
LTC3589/LTC3589-1
22
3589fc
Operating Frequency
The switching frequency of each of the LTC3589/LTC3589-1
step-down switching regulators may be independently set
using I2C command register bits B1DTV2[5], B2DTV2[5]
and B3DTV2[5]. The power-on default frequency is
2.25MHz. Writing bit BxDTV2[5] HIGH will reduce the
switching frequency to 1.125MHz. Selection of the op-
erating frequency is determined by desired efciency,
component size and converter duty cycle.
Operation at lower frequency improves efciency by reduc-
ing internal gate charge and switching losses but requires
larger inductance and capacitance values for comparable
output ripple voltage. The lowest duty cycle of the step-
down switching regulator is determined by the converters
minimum on-time. Minimum on-time is the shortest time
durationthattheconverteriscapableofturningitstopPMOS
on and off again. The time consists of the gate charge time
OPERATION
plus internal delays associated with peak current sensing.
The minimum on-time of the LTC3589/LTC3589-1 is ap-
proximately 90ns. If the duty cycle falls below what can be
accommodated by the minimum on-time, the converter will
begin to skip cycles. The output voltage will continue to be
regulated but the ripple voltage and current will increase.
With the switching frequency set to 2.25MHz, the minimum
supported duty cycle is 20%. Switching at 1.125MHz the
converter can support a 10% duty cycle.
Phase Selection
To reduce the cycle by cycle peak current drawn by the
switchingregulators,theclockphaseofeachoftheLTC3589/
LTC3589-1 step-down switching regulators can be set
using I2C command register bits B1DTV2[6], B2DTV2[6]
and B3DTV2[6]. The internal full-rate clock has a nominal
duty cycle of 20% while the half-rate clocks have a 50%
duty cycle. Setting the command register bits high will
delay the start of each converter switching cycle by 20%
or 50% depending on the selected operating frequency.
Inductor Selection
The choice of step-down switching regulator inductor inu-
ences the efciency of the converter and the magnitude of
the output voltage ripple. Larger inductance values reduce
inductor current ripple and therefore lower output voltage
ripple. A larger value inductor improves efciency by low-
ering the peak current to be closer to the average output
current. Larger inductors, however, generally have higher
series resistance that counters the efciency advantage
of reduced peak current.
Inductor ripple current is a function of switching frequency,
inductance, VIN, and VOUT, as shown in this equation:
IL =
1
f L
VOUT 1–
VOUT
VIN
In an example application the LTC3589/LTC3589-1 step-
down switching regulator 3 has a maximum load of 1A,
VIN equals 3.8V, and VOUT is set for 1.2V. A good starting
design point for inductor ripple is 30% of output current
or 300mA. Using the equation for ripple current, a 1.2μH
inductor should be selected.
Table 7. Step-Down Switching Regulator 3 Command Register
Settings
COMMAND
REGISTER[BIT]
VALUE
SETTING
SCR1[5-4]
00*
01
10
Pulse-Skipping Mode
Burst Mode Operation
Forced Continuous Mode
OVEN[2]
0*
1
Disable
Enable
SCR2[2]
0*
1
Wait for Output Below 300mV Before Enable
Enable Immediately
VCCR[5]
0*
1
Select Register B3DTV1 (V1) Reference
Select Register B3DTV2 (V2) Reference
VCCR[4]
1
Initiate Dynamic Voltage Slew
VRRCR[5-4]
00
01
10
11*
Reference Slew Rate = 0.88mV/μs
Reference Slew Rate = 1.75mV/μs
Reference Slew Rate = 3.5mV/μs
Reference Slew Rate = 7mV/μs
B3DTV1[5]
0*
1
Force PGOOD Low When Slewing
Normal PGOOD Operation When Slewing
B3DTV1[4-0]
11001*
DAC Dynamic Target Voltage V1
B3DTV2[4-0]
11001*
DAC Dynamic Target Voltage V2
B3DTV2[5]
0*
1
2.25MHz Switching Frequency
1.125MHz Switching Frequency
B3DTV2[6]
0*
1
Switch on Clock Phase 1
Switch on Clock Phase 2
B3DTV2[7]
0*
1
Shutdown Regulator 3 Normally
Keep Regulator 3 Alive
* Denotes Default Power-On Value
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3609IWKG#PBF | SWITCHING REGULATOR, PQCC52 |
| LTC3609IWKG#TRPBF | SWITCHING REGULATOR, PQCC52 |
| LTC3614IUDD#PBF | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3614EUDD#PBF | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| LTC3615EFE-1#TRPBF | SWITCHING REGULATOR, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3589IUJ-2#PBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589IUJ-2#TRPBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589IUJ-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589IUJ-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3600EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。