- 您现在的位置：买卖IC网 > PDF目录14075 > LTC3601EMSE#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 1.5A 16MSOP PDF资料下载
参数资料
| 型号： | LTC3601EMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1.5A 16MSOP |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 14.52 V |
| 输入电压： | 4 V ~ 15 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 800kHz ~ 4MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
LTC3601
PIN FUNCTIONS
(QFN/MSE)
MODE/SYNC (Pin 1/Pin 15): Mode Selection and External
Synchronization Input Pin. This pin places the LTC3601
into forced continuous operation when tied to ground.
High ef?ciency Burst Mode operation is enabled by either
?oating this pin or by tying this pin to INTV CC . When driven
with an external clock, an internal phase-locked loop will
synchronize the phase and frequency of the internal oscil-
lator to that of the incoming clock signal. During external
clock synchronization, the LTC3601 will default to forced
continuous operation.
PGOOD (Pin 2/Pin 16): Open-Drain Power Good Output
Pin. PGOOD is pulled to ground when the voltage at the
FB pin is not within 8% (typical) of the internal 0.6V refer-
ence. PGOOD becomes high impedance once the voltage
at the FB pin returns to within ±5% (typical) of the internal
reference.
SW (Pins 3, 4/Pins 1, 2): Switch Node Output Pin. Con-
nect this pin to the SW side of the external inductor. The
normal operation voltage swing of this pin ranges from
ground to PV IN .
BOOST (Pin 6/Pin 5): Boosted Floating Driver Supply
Pin. The (+) terminal of the external bootstrap capacitor
connects to this pin while the (–) terminal connects to
the SW pin. The normal operation voltage swing of this
pin ranges from a diode voltage drop below INTV CC up
to PV IN + INTV CC .
INTV CC (Pin 7/Pin 6): Internal 3.3V Regulator Output Pin.
This pin should be decoupled to PGND with a low ESR
ceramic capacitor of 1μF or more.
V ON (Pin 8/Pin 7): On-Time Voltage Input Pin. This pin
sets the voltage trip point for the on-time comparator.
Connect this pin to the regulated output to make the on-
time proportional to the output voltage when V OUT ≤ 6V. If
V OUT > 6V, switching frequency may become higher than
the set frequency. The pin impedance is normally 180kΩ.
SGND (Pin 9/Exposed Pad Pin 17): Signal Ground Pin.
This pin should have a low noise connection to reference
ground. The feedback resistor network, external compen-
sation network and RT resistor should be connected to
this ground. In the MSE package, the exposed pad must
RT (Pin 10/Pin 8): Oscillator Frequency Program Pin. Con-
nect an external resistor, between 80k to 400k, from this
pin to SGND to program the LTC3601 switching frequency
from 800kHz to 4MHz. When RT is tied to INTV CC , the
switching frequency will default to 2MHz.
FB (Pin 11/Pin 9): Output Voltage Feedback Pin. Input to
the error ampli?er that compares the feedback voltage to
the internal 0.6V reference voltage. Connect this pin to
the appropriate resistor divider network to program the
desired output voltage.
ITH (Pin 12/Pin 10): Error Ampli?er Output and Switching
Regulator Compensation Pin. Connect this pin to appro-
priate external components to compensate the regulator
loop frequency response. Connect this pin to INTV CC to
use the default internal compensation.
TRACK (Pin 13/Pin 11): Output Voltage Tracking and Soft-
Start Input Pin. Forcing a voltage below 0.6V on this pin
overrides the internal reference input to the error ampli?er.
The LTC3601 will servo the FB pin to the TRACK voltage
under this condition. Above 0.6V, the tracking function
stops and the internal reference resumes control of the
error ampli?er. An internal 1.4μA pull-up current from
INTV CC allows a soft-start function to be implemented
by connecting an external capacitor between this pin and
ground. See Applications Information section for more
details.
RUN (Pin 14/Pin 12): Regulator Enable Pin. Enables chip
operation by applying a voltage above 1.25V. A voltage
below 1V on this pin places the part into shutdown. Do
not ?oat this pin.
V IN (Pins 15, 16/Pins 13, 14): Main Power Supply Input
Pins. These pins should be closely decoupled to PGND
with a low ESR capacitor of 10μF or more.
PGND (Exposed Pad Pin 17/Pins 3, 4): Power Ground Pin.
The (–) terminal of the input bypass capacitor, C IN , and the
(–) terminal of the output capacitor, C OUT , should be tied
to this pin with a low impedance connection. In the QFN
package the exposed pad must be soldered to the PCB to
provide low impedance electrical contact to ground and
good thermal contact to the PCB.
be soldered to the PCB to provide a good thermal contact
to the PCB.
3601fb
7
相关PDF资料 |
PDF描述 |
|---|---|
| HM71-30102LFTR | HIGH PERF LOW COST INDUCTORS |
| HM71-30681LFTR | HIGH PERF LOW COST INDUCTORS |
| LTC3565IDD#TRPBF | IC REG BUCK SYNC ADJ 1.25A 10DFN |
| MAX6869UK21D2L+T | IC MPU SUPERVISOR SOT23-5 |
| HM71-30471LFTR | HIGH PERF LOW COST INDUCTORS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3601EUD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3601EUD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3601EUDPBF | 制造商:Linear Technology 功能描述:DC-DC Converter Step-Down 4-15V QFN16EP |
| LTC3601IMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LTC3601IMSE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。