- 您现在的位置：买卖IC网 > PDF目录14797 > LTC3603EUF#PBF (Linear Technology)IC REG BUCK SYNC ADJ 2.5A 20QFN PDF资料下载
参数资料
| 型号： | LTC3603EUF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 2.5A 20QFN |
| 标准包装： | 91 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 14.5 V |
| 输入电压： | 4.5 V ~ 15 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 300kHz ~ 3MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
LTC3603
APPLICATIONS INFORMATION
V OUT ?
V OUT
? ? ? 1– V
L = ? ?
1.15 ? 10 11
R OSC = – 10k
Δ I L = ? OUT ? ? ? 1– OUT ?
The basic LTC3603 application circuit is shown on the front
page of this data sheet. External component selection is
determined by the maximum load current and begins with
the selection of the inductor value and operating frequency
followed by C IN and C OUT .
Operating Frequency
Selection of the operating frequency is a trade-off between
efficiency and component size. High frequency operation
allows the use of smaller inductor and capacitor values.
Operation at lower frequencies improves efficiency by
reducing internal gate charge and switching losses but
requires larger inductance values and/or capacitance to
maintain low output ripple voltage. The operating frequency
of the LTC3603 is determined by an external resistor that is
connected between the RT pin and ground. The value of the
resistor sets the ramp current that is used to charge and
discharge an internal timing capacitor within the oscillator
and can be calculated by using the following equation:
f(Hz)
Although frequencies as high as 3MHz are possible, the
minimum on-time of the LTC3603 imposes a minimum
limit on the operating duty cycle. The minimum on-time
is typically 95ns. Therefore, the minimum duty cycle is
equal to 100 ? 95ns ? f(Hz).
Inductor Selection
For a given input and output voltage, the inductor value
and operating frequency determine the ripple current. The
ripple current D I L increases with higher V IN and decreases
with higher inductance.
? V ? ? V ?
? fL ? ? V IN ?
Having a lower ripple current reduces the ESR losses
in the output capacitors and the output voltage ripple.
Highest efficiency operation is achieved at low frequency
with small ripple current. This, however, requires a large
inductor.
A reasonable starting point for selecting the ripple current
is D I L = 0.4(I MAX ), where I MAX is the maximum output
current. The largest ripple current occurs at the highest
V IN . To guarantee that the ripple current stays below a
specified maximum, the inductor value should be chosen
according to the following equation:
? ? ?
? f Δ I L(MAX) ? ? IN(MAX) ?
The inductor value will also have an effect on Burst Mode
operation. The transition from low current operation
begins when the peak inductor current falls below a level
set by the burst clamp. Lower inductor values result in
higher ripple current which causes this to occur at lower
load currents. This causes a dip in efficiency in the upper
range of low current operation. In Burst Mode operation,
lower inductance values will cause the burst frequency
to increase.
Inductor Core Selection
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of the more expensive ferrite cores. Actual
core loss is independent of core size for a fixed inductor
value but it is very dependent on the inductance selected.
As the inductance increases, core losses decrease. Un-
fortunately, increased inductance requires more turns of
wire and therefore copper losses will increase.
Ferrite designs have very low core losses and are pre-
ferred at high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates hard , which means that
inductance collapses abruptly when the peak design current
is exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
Different core materials and shapes will change the
size/current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy ma-
terials are small and do not radiate energy but generally
cost more than powdered iron core inductors with similar
10
For more information www.linear.com/LTC3603
3603fc
相关PDF资料 |
PDF描述 |
|---|---|
| 1140-2R2M | CHOKE RF RADIAL 2.2UH 20% |
| LGU1K182MELB | CAP ALUM 1800UF 80V 20% SNAP |
| LGU2P471MELB | CAP ALUM 470UF 220V 20% SNAP |
| MAX6423XS37+T | IC MPU/RESET CIRC 3.70V SC70-4 |
| MAX6423XS39+T | IC MPU/RESET CIRC 3.90V SC70-4 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3603IMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3603IMSE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3603IUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3603IUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 2.5A 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3604EMSE#PBF | 功能描述:IC REG BUCK SYNC 2.5A 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。