- 您现在的位置：买卖IC网 > PDF目录39425 > LTC3604IUD#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PQCC16 PDF资料下载
参数资料
| 型号： | LTC3604IUD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PQCC16 |
| 封装： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-220WEED-2, QFN-16 |
| 文件页数： | 9/24页 |
| 文件大小： | 277K |
| 代理商： | LTC3604IUD#TRPBF |
LTC3604
17
3604f
Figure 5 is a temperature derating curve based on the
DC1353A demo board. It can be used to estimate the
maximum allowable ambient temperature for given DC
load currents in order to avoid exceeding the maximum
operating junction temperature of 125°C.
Board Layout Considerations
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3604.
1. Do the capacitors CIN connect to VIN and PGND as close
to the pins as possible? These capacitors provide the AC
current to the internal power MOSFETs and drivers. The
(–) plate of CIN should be closely connected to PGND
and the (–) plate of COUT.
2. The output capacitor, COUT, and inductor L1 should
be closely connected to minimize loss. The (–) plate
of COUT should be closely connected to PGND and the
(–) plate of CIN.
3. The resistive divider, R1 and R2, must be connected
between the (+) plate of COUT and a ground line termi-
nated near SGND. The feedback signal, VFB, should be
routed away from noisy components and traces such as
the SW line, and its trace length should be minimized.
In addition, RT and the loop compensation components
should be terminated to SGND.
4. Keep sensitive components away from the SW pin. The
RRT resistor, the feedback resistors, the compensation
components, and the INTVCCbypasscapacitorshouldall
be routed away from the SW trace and the inductor.
5. A ground plane is preferred, but if not available the
signal and power grounds should be segregated with
both connecting to a common, low noise reference
point. The point at which the ground terminals of the
VIN and VOUT bypass capacitors are connected makes a
good, low noise reference point. The connection to the
PGND pin should be made with a minimal resistance
trace from the reference point.
6. Flood all unused areas on all layers with copper in order
to reduce the temperature rise of power components.
These copper areas should be connected to the exposed
backside connection of the IC.
APPLICATIONS INFORMATION
Figure 5. Load Current vs Ambient Temperature
TEMPERATURE (°C)
25
0
LOAD
CURRENT
(A)
0.5
1.0
1.5
2.0
2.5
3.0
50
75
100
125
3604 F05
VIN = 12V
VOUT = 1.8V
fO = 1MHz
DC1353A
Junction Temperature Measurement
The junction-to-ambient thermal resistance will vary de-
pending on the size and amount of heat sinking copper on
the PCB board where the part is mounted, as well as the
amount of air ow on the device. One of the ways to mea-
sure the junction temperature directly is to use the internal
junction diode on one of the pins (PGOOD) to measure
its diode voltage change based on ambient temperature
change. First remove any external passive component on
the PGOOD pin, then pull out 100μA from the PGOOD pin
to turn on its internal junction diode and bias the PGOOD
pin to a negative voltage. With no output current load,
measure the PGOOD voltage at an ambient temperature
of 25°C, 75°C and 125°C to establish a slope relationship
between the delta voltage on PGOOD and delta ambient
temperature. Once this slope is established, then the junc-
tion temperature rise can be measured as a function of
power loss in the package with corresponding output load
current. Keep in mind that doing so will violate absolute
maximum voltage ratings on the PGOOD pin, however,
with the limited current, no damage will result.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3604IUD#PBF | SWITCHING REGULATOR, PQCC16 |
| LTC3604EMSE#PBF | SWITCHING REGULATOR, PDSO16 |
| LTC3604EMSE#TRPBF | SWITCHING REGULATOR, PDSO16 |
| LTC3604IMSE#TRPBF | SWITCHING REGULATOR, PDSO16 |
| LTC3775EMSE#TRPBF | SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3605AEUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AEUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AIUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AIUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605EUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。