- 您现在的位置：买卖IC网 > PDF目录1830 > LTC3606BIDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.8A 8DFN PDF资料下载
参数资料
| 型号： | LTC3606BIDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.8A 8DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-DFN-EP（3x3） |
LTC3606B
APPLICATIONS INFORMATION
2. The switching current is the sum of the MOSFET driver
and control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge dQ moves
from V IN to ground. The resulting dQ/dt is a current
out of V IN that is typically much larger than the DC bias
current. In continuous mode, I GATECHG = f O (Q T + Q B ),
where Q T and Q B are the gate charges of the internal
top and bottom MOSFET switches. The gate charge
losses are proportional to V IN and thus their effects
will be more pronounced at higher supply voltages.
3. I 2 R losses are calculated from the DC resistances of
the internal switches, R SW , and external inductor, R L .
In continuous mode, the average output current ?ows
through inductor L, but is “chopped” between the internal
top and bottom switches. Thus, the series resistance
looking into the SW pin is a function of both top and
bottom MOSFET R DS(ON) and the duty cycle (DC) as
follows:
R SW = (R DS(ON)TOP ) ? (DC) + (R DS(ON)BOT ) ? (1– DC)
The R DS(ON) for both the top and bottom MOSFETs can be
obtained from the Typical Performance Characteristics
curves. Thus, to obtain I 2 R losses:
I 2 R losses = I OUT 2 ? (R SW + R L )
4. Other “hidden” losses, such as copper trace and
internal battery resistances, can account for additional
ef?ciency degradations in portable systems. It is very
important to include these “system” level losses in
the design of a system. The internal battery and fuse
resistance losses can be minimized by making sure that
C IN has adequate charge storage and very low ESR at
Thermal Considerations
In a majority of applications, the LTC3606B does not
dissipate much heat due to its high ef?ciency. In the
unlikely event that the junction temperature somehow
reaches approximately 150°C, both power switches will be
turned off and the SW node will become high impedance.
The goal of the following thermal analysis is to determine
whether the power dissipated causes enough temperature
rise to exceed the maximum junction temperature (125°C)
of the part. The temperature rise is given by:
T RISE = P D ? θ JA
where P D is the power dissipated by the regulator and
θ JA is the thermal resistance from the junction of the die
to the ambient temperature. The junction temperature,
T J , is given by:
T J = T RISE + T AMBIENT
As a worst-case example, consider the case when the
LTC3606B is in dropout at an input voltage of 2.7V with
a load current of 800mA and an ambient temperature of
70°C. From the Typical Performance Characteristics graph
of Switch Resistance, the R DS(ON) of the switch is 0.33Ω.
Therefore, the power dissipated is:
P D = I OUT 2 ? R DS(ON) = 212mV
Given that the thermal resistance of a properly soldered
DFN package is approximately 40°C/W, the junction
temperature of an LTC3606B device operating in a 70°C
ambient temperature is approximately:
T J = (0.212W ? 40°C/W) + 70°C = 78.5°C
which is well below the absolute maximum junction
temperature of 125°C.
the switching frequency. Other losses, including diode
conduction losses during dead-time, and inductor
core losses, generally account for less than 2% total
additional loss.
3606bfb
13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3608IWKG#PBF | IC REG BUCK SYNC ADJ 8A 52QFN |
| LTC3609IWKG#TRPBF | IC REG BUCK SYNC ADJ 6A 52QFN |
| LTC3610IWP#PBF | IC REG BUCK SYNC ADJ 12A 64QFN |
| LTC3611IWP#TRPBF | IC REG BUCK SYNC ADJ 10A 64QFN |
| LTC3612EFE#PBF | IC REG BUCK SYNC ADJ 3A 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3607EUD#PBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 0.6A 16QFN 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, QFN-16, Primary Input Voltage:15V, No. of Outputs:2, Output Current:600mA, No. of Pins:16, Operating Temperature Min:-40C, Operating Temperature Max:125C, MSL:-, Package / Case:16-QFN , RoHS Compliant: Yes 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, 15V Dual 600mA Monolithic Synchronous Step-Down DC/DC Regul |
| LTC3607EUD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 0.6A 16QFN 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, 15V Dual 600mA Monolithic Synchronous Step-Down DC/DC Regul |
| LTC3608EWKG#PBF | 功能描述:IC REG BUCK SYNC ADJ 8A 52QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LTC3608EWKG#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 8A 52QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3608IWKG#PBF | 功能描述:IC REG BUCK SYNC ADJ 8A 52QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。