- 您现在的位置：买卖IC网 > PDF目录13926 > LTC3612IUDC#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 3A 20QFN PDF资料下载
参数资料
| 型号： | LTC3612IUDC#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 20QFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 5.5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 300kHz ~ 4MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 20-QFN（3x4） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3612
APPLICATIONS INFORMATION
? I L = ? OUT ? ? ? 1– OUT ?
FrequencySynchronization
The LTC3612’s internal oscillator can be synchronized to
an external frequency by applying a square wave clock
signal to the RT/SYNC pin. During synchronization, the top
switch turn-on is locked to the falling edge of the external
frequency source. The synchronization frequency range
is 300kHz to 4MHz. During synchronization all operation
modes can be selected.
It is recommended that the regulator is powered down
(RUN pin to ground) before removing the clock signal on
the RT/SYNC pin in order to reduce inductor current ripple.
AC coupling should be used if the external clock generator
cannot provide a continuous clock signal throughout start-
up, operation and shutdown of the LTC3612. The size of
capacitor C SYNC depends on parasitic capacitance on the
RT/SYNC pin and is typically in the range of 10pF to 22pF
Inductor Selection
For a given input and output voltage, the inductor value
and operating frequency determine the ripple current. The
ripple current ? I L increases with higher V IN and decreases
with higher inductance:
? V ? ? V ?
? f SW ?L ? ? V IN ?
Having a lower ripple current reduces the core losses
in the inductor, the ESR losses in the output capacitors
and the output voltage ripple. A reasonable starting point
for selecting the ripple current is ? I L = 0.3 ? I OUT(MAX) .
The largest ripple current occurs at the highest V IN . To
guarantee that the ripple current stays below a specified
maximum, the inductor value should be chosen according
to the following equation:
V OUT ?
V OUT
? ? ? 1– V
L = ? ?
V IN
V IN
0.4V
R T
V IN
LTC3612
SV IN
RT/SYNC
LTC3612
SV IN
RT/SYNC
SGND
LTC3612
SV IN
RT/SYNC
f OSC
2.25MHz
f OSC ∝ 1/R T
f OSC
1/T P
? ? ?
? f SW ? ? I L(MAX) ? ? IN ?
The inductor value will also have an effect on Burst Mode
operation. The transition to low current operation begins
when the peak inductor current falls below a level set by the
burst clamp. Lower inductor values result in higher ripple
current which causes this to occur at lower load currents.
This causes a dip in efficiency in the upper range of low
current operation. In Burst Mode operation, lower induc-
tance values will cause the burst frequency to increase.
V IN
SV IN
f OSC
SGND
1.2V
0.3V
T P
LTC3612
C SYNC
RT/SYNC 1/T P
SGND
R T
3612 F02
Figure 2. Setting the Switching Frequency
Inductor Core Selection
Once the value for L is known, the type of inductor must be
selected. Actual core loss is independent of core size for
fixed inductor value, but it is very dependent on the induc-
tance selected. As the inductance increases, core losses de-
crease. Unfortunately, increased inductance requires more
turns of wire and therefore, copper losses will increase.
Ferrite designs have very low core losses and are pre-
ferred at high switching frequencies, so design goals
can concentrate on copper loss and preventing satura-
tion. Ferrite core material saturates “hard,” meaning
that inductance collapses abruptly when the peak design
current is exceeded. This results in an abrupt increase in
3612fb
For more information www.linear.com/LTC3612
15
相关PDF资料 |
PDF描述 |
|---|---|
| ECC44DRYI | CONN EDGECARD 88POS DIP .100 SLD |
| MAX6719AUTLTD2+T | IC SUPERVISOR MPU SOT23-6 |
| LTC3569IUD#TRPBF | IC REG BUCK SYNC ADJ TRPL 20QFN |
| MAX6720AUTTGD6+T | IC SUPERVISOR MPU SOT23-6 |
| ESC40DRXI | CONN EDGECARD 80POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3613EWKH#PBF | 功能描述:IC REG BUCK SYNC ADJ 15A 56-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3613EWKH#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 15A 56QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3613IWKH#PBF | 功能描述:IC REG BUCK SYNC ADJ 15A 56QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3613IWKH#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 15A 56QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3614EUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
发布紧急采购，3分钟左右您将得到回复。