- 您现在的位置：买卖IC网 > PDF目录79678 > LTC3614EUDD#TRPBF (LINEAR TECHNOLOGY CORP) 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 PDF资料下载
参数资料
| 型号： | LTC3614EUDD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 10.5 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封装： | 3 X 5 MM, LEAD FREE, PLASTIC, QFN-24 |
| 文件页数： | 9/30页 |
| 文件大小： | 438K |
| 代理商： | LTC3614EUDD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3614
17
3614fa
Output Voltage Programming
The output voltage is set by an external resistive divider
according to the following equation:
VOUT = 0.6 1+
R1
R2
V
The resistive divider allows pin VFB to sense a fraction of
the output voltage as shown in Figure 1.
Burst Clamp Programming
If the voltage on the MODE pin is less than 0.8V, Burst
Mode operation is enabled.
If the voltage on the MODE pin is less than 0.3V, the internal
default burst clamp level is selected. The minimum voltage
on the ITH pin is typically 525mV (internal clamp).
If the voltage is between 0.45V and 0.8V, the voltage on
the MODE pin (VBURST) is equal to the minimum voltage
on the ITH pin (external clamp) and determines the burst
clamp level IBURST (typically from 0A to 7A).
When the ITH voltage falls below the internal (or external)
clamp voltage, the sleep state is enabled.
As the output load current drops, the peak inductor current
decreases to keep the output voltage in regulation. When
the output load current demands a peak inductor current
that is less than IBURST, the burst clamp will force the peak
inductor current to remain equal to IBURST regardless of
further reductions in the load current.
Since the average inductor current is greater than the output
load current, the voltage on the ITH pin will decrease. When
the ITH voltage drops, sleep mode is enabled in which
both power switches are shut off along with most of the
circuitry to minimize power consumption. All circuitry is
turned back on and the power switches resume opera-
tion when the output voltage drops out of regulation. The
value for IBURST is determined by the desired amount of
output voltage ripple. As the value of IBURST increases, the
sleep period between pulses and the output voltage ripple
increase. Note that for very high VBURST voltage settings,
the power good comparator may trip, since the output
ripple may get bigger than the power good window.
Pulse-skipping mode, which is a compromise between low
output voltage ripple and efciency, can be implemented
by connecting MODE to SVIN. This sets IBURST to 0A. In
this condition, the peak inductor current is limited by the
minimum on-time of the current comparator. The lowest
output voltage ripple is achieved while still operating
discontinuously. During very light output loads, pulse-
skipping allows only a few switching cycles to skip while
maintaining the output voltage in regulation.
Internal and External Compensation
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC load current.
When a load step occurs, VOUT shifts by an amount equal
to ΔILOAD(ESR), where ESR is the effective series resistance
of COUT. ΔILOAD also begins to charge or discharge COUT,
generating the feedback error signal that forces the regula-
tor to adapt to the current change and return VOUT to its
steady-state value. During this recovery time VOUT can
be monitored for excessive overshoot or ringing, which
would indicate a stability problem. The availability of the
ITH pin allows the transient response to be optimized over
a wide range of output capacitance.
The ITH external components (RC and CC) shown in Fig-
ure 1 provide adequate compensation as a starting point
for most applications. The values can be modied slightly
to optimize transient response once the nal PCB layout
is done and the particular output capacitor type and value
have been determined. The output capacitors need to be
selected because the various types and values determine
the loop gain and phase. The gain of the loop will be in-
creased by increasing RC and the bandwidth of the loop
will be increased by decreasing CC. If RC is increased by
the same factor that CC is decreased, the zero frequency
will be kept the same, thereby keeping the phase shift the
same in the most critical frequency range of the feedback
loop. The output voltage settling behavior is related to the
stability of the closed-loop system. The external capaci-
tor, CC1, (Figure 1) is not needed for loop stability, but it
helps lter out any high frequency noise that may couple
onto that node.
APPLICATIONS INFORMATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3859IUHF#PBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PQCC38 |
| LRS-59-28 | 1-OUTPUT 1456 W AC-DC REG PWR SUPPLY MODULE |
| LPT44-T | 3-OUTPUT 55 W AC-DC REG PWR SUPPLY MODULE |
| LM2576HVBU | 3.5 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, PSSO5 |
| LWT-30H-5FF | 3-OUTPUT 30 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3614IUDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3614IUDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3614MPUDD#PBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN |
| LTC3614MPUDD#TRPBF | 制造商:Linear Technology 功能描述:IC REG BUCK SYNC ADJ 4A 24QFN |
| LTC3615EFE#PBF | 功能描述:IC REG BUCK SYNC ADJ 3A 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。