- 您现在的位置：买卖IC网 > PDF目录14042 > LTC3619BIMSE#PBF (Linear Technology)IC REG BUCK SYNC ADJ DL 10MSOP PDF资料下载
参数资料
| 型号： | LTC3619BIMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/20页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ DL 10MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 400mA，800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
LTC3619B
OPERATION
R LIM =
Short-CircuitProtection
When either regulator output is shorted to ground, the
corresponding internal N-channel switch is forced on for
a longer time period for each cycle in order to allow the
inductor to discharge, thus preventing inductor current
runaway. This technique has the effect of decreasing
switching frequency. Once the short is removed, normal
operation resumes and the regulator output will return to
its nominal voltage.
Input Current Limit
Internal current sense circuitry in each channel measures
the inductor current through the voltage drop across the
power PFET switch and forces the same voltage across
the small sense PFET. The voltage across the small sense
PFET generates a current representing 1/55,000th of the
inductor current during the on-cycle. The current out of
RLIM pin is the summed representation of the inductor
currents from both channels, which can be expressed in
the following equation.
I RLIM = I OUT1 ? D 1 ? K1 + I OUT2 ? D 2 ? K2,
where D1 = V OUT1 /V IN and D2 = V OUT2 /V IN are the duty
cycle of channel 1 and 2, respectively.
K1 is the ratio R DS(ON) (power PFET)/R DS(ON) (sense PFET)
of channel 1, and K2 is the ratio R DS(ON) (power PFET)/
R DS(ON) (sense PFET) of channel 2. The ratio of the power
PFET to the sense PFET is trimmed to within 2%.
Given that both PFETs are carefully laid out and matched,
their temperature and voltage coefficient effects will be
similar and their terms be canceled out in the equation. In
that case, the constants K1 and K2 will only be dependent
on area scaling, which is trimmed to within 2%. Thus, the
I RLIM current will track the input current very well over
varying temperature and V IN .
The RLIM pin can be grounded to disable input current
limit function.
Programming Input Current Limit
Selection of one external R LIM resistor will program the
input current limit. The current limit can be programmed
from 200mA up to I PEAK current. As the input current
increases, R LIM voltage will follow. When R LIM reaches
the internal comparator threshold of 1V, channel 2’s
power PFET on-time will be shortened, thereby, limiting
the input current.
Use the following equation to select the R LIM resistance
that corresponds to the input current limit.
55k ? ? A
I DC (A)
I DC is the input current (at V IN ) to be limited. The following
are some R LIM values with the corresponding current limit.
R LIM I DC
91.6k 600mA
110k 500mA
137.5k 400mA
Selection of C LIM Capacitance
Since I RLIM current is a function of the inductor current,
its dependency on the duty cycle cannot be ignored. Thus,
a C LIM capacitor is needed to integrate the I RLIM current
and smooth out transient currents. The LTC3619B is stable
with any size capacitance >100pF at the RLIM pin.
Each application input current limit will call for different
C LIM value to optimize its response time. Using a large C LIM
capacitor requires longer time for the RLIM pin voltage
to charge. For example, consider the application 500mA
input current limit, 5V input and 1A, 2.5V output with a
50% duty cycle. When an instantaneous 1A output pulse is
applied, the current out of the RLIM pin becomes 1A/55k
= 18.2μA during the 50% on-time or 9.1μA full duty cycle.
With a C LIM capacitor of 1μF, R LIM of 116k, and using I =
CdV/dt, it will take 110ms for C LIM to charge from 0V to
1V. This is the time after which the LTC3619B will start
input current limiting. Any current within this time must be
considered in each application to determine if it is tolerable.
3619bfb
9
相关PDF资料 |
PDF描述 |
|---|---|
| V24B24E200B2 | CONVERTER MOD DC/DC 24V 200W |
| LTC3619BIDD#PBF | IC REG BUCK SYNC ADJ DL 10DFN |
| LT3990EMSE-5#TRPBF | IC REG BUCK ADJ 0.35A 16MSOP |
| LT3990EMSE-3.3#TRPBF | IC REG BUCK ADJ 0.35A 16MSOP |
| V24B24E200B | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3619EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LTC3619EDD#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-DOWN DC/DC CONVERTER DFN-10 |
| LTC3619EDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ DL 10DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3619EMSE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3619EMSE#PBF | 制造商:Linear Technology 功能描述:IC SYNC STEP-DOWN DC/DC CONVERTER MSOP10 |
发布紧急采购，3分钟左右您将得到回复。