参数资料
型号: LTC3633IUFD#PBF
厂商: Linear Technology
文件页数: 20/28页
文件大小: 0K
描述: IC REG BUCK ADJ 3A DL 28QFN
标准包装: 73
类型: 降压(降压)
输出类型: 可调式
输出数: 2
输出电压: 0.6 V ~ 14.7 V
输入电压: 3.6 V ~ 15 V
PWM 型: 电流模式,混合
频率 - 开关: 500kHz ~ 4MHz
电流 - 输出: 3A
同步整流器:
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 28-WFQFN 裸露焊盘
包装: 管件
供应商设备封装: 28-QFN(4x5)
LTC3633
APPLICATIONS INFORMATION
R DS(ON)TOP ?
+R DS(ON)BOT ?
= 89m?
0.5
is to determine whether the power dissipated exceeds the
maximum junction temperature of the part. The tempera-
ture rise is given by:
T RISE = P D ? θ JA
As an example, consider the case when one of the regula-
tors is used in an application where V IN = 12V, I OUT = 2A,
frequency = 2MHz, V OUT = 1.8V. From the R DS(ON) graphs
in the Typical Performance Characteristics section, the top
switch on-resistance is nominally 140mΩ and the bottom
switch on-resistance is nominally 80mΩ at 70°C ambient.
The equivalent power MOSFET resistance R SW is:
1.8V           10.2V
12V 12V
From the previous section’s discussion on gate drive, we
estimate the total gate drive current through the LDO to be
2MHz ? 2.3nC = 4.6mA, and I Q of one channel is 0.65mA
(see Electrical Characteristics). Therefore, the total power
dissipated by a single regulator is:
P D = I OUT2 ? R SW + V IN ? (I GATECHG + I Q )
P D = (2A) 2 ? (0.089Ω) + (12V) ? (4.6mA + 0.65mA)
= 0.419W
Running two regulators under the same conditions would
result in a power dissipation of 0.838W. The QFN 5mm
× 4mm package junction-to-ambient thermal resistance,
θ JA , is around 43°C/W. Therefore, the junction temperature
of the regulator operating in a 70°C ambient temperature
is approximately:
T J = 0.838W ? 43°C/W + 70°C = 106°C
which is below the maximum junction temperature of
125°C. With higher ambient temperatures, a heat sink or
cooling fan should be considered to drop the junction-
to-ambient thermal resistance. Alternatively, the TSSOP
package may be a better choice for high power applications,
since it has better thermal properties than the QFN package.
Remembering that the above junction temperature is
obtained from an R DS(ON) at 70°C, we might recalculate
the junction temperature based on a higher R DS(ON) since
it increases with temperature. Redoing the calculation
assuming that R SW increased 12% at 106°C yields a new
junction temperature of 109°C. If the application calls for
a higher ambient temperature and/or higher load currents,
care should be taken to reduce the temperature rise of the
part by using a heat sink or air flow.
Figure 7 is a temperature derating curve based on the
DC1347 demo board (QFN package). It can be used to
estimate the maximum allowable ambient temperature
for given DC load currents in order to avoid exceeding
the maximum operating junction temperature of 125°C.
3.5
3.0
2.5
2.0
1.5
1.0
CH2 LOAD = 0A
CH2 LOAD = 1A
CH2 LOAD = 2A
CH2 LOAD = 3A
0
0 25 50 75 100 125
MAXIMUM ALLOWABLE AMBIENT
TEMPERATURE (°C)
3633 F07
Figure 7. Temperature Derating Curve for DC1347 Demo Circuit
Junction Temperature Measurement
The junction-to-ambient thermal resistance will vary de-
pending on the size and amount of heat sinking copper
on the PCB board where the part is mounted, as well as
the amount of air flow on the device. In order to properly
evaluate this thermal resistance, the junction temperature
needs to be measured. A clever way to measure the junc-
tion temperature directly is to use the internal junction
diode on one of the pins (PGOOD) to measure its diode
voltage change based on ambient temperature change.
First remove any external passive component on the
PGOOD pin, then pull out 100μA from the PGOOD pin to
turn on its internal junction diode and bias the PGOOD
pin to a negative voltage. With no output current load,
measure the PGOOD voltage at an ambient temperature
of 25°C, 75°C and 125°C to establish a slope relationship
between the delta voltage on PGOOD and delta ambient
temperature. Once this slope is established, then the
junction temperature rise can be measured as a function
3633fc
20
For more information www.linear.com/LTC3633
相关PDF资料
PDF描述
HC2-1R0-R INDUCTOR POWER HI CURR 1UH SMD
LT1374HVCFE#PBF IC REG BUCK ADJ 4.5A 16TSSOP
GEM22DTBD-S273 CONN EDGECARD 44POS R/A .156 SLD
380LQ681M350A032 CAP ALUM 680UF 350V 20% SNAP
LLG2W271MELZ45 CAP ALUM 270UF 450V 20% CAN
相关代理商/技术参数
参数描述
LTC3634EFE#PBF 功能描述:IC REG 15V 3A STEP DOWN 28-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器,DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP(0.173",4.40mm 宽) 供应商设备封装:30-TSSOP 包装:带卷 (TR)
LTC3634EFE#TRPBF 功能描述:IC CONV DDR DDR2 DDR3 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器,Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN(7x7) 包装:管件
LTC3634EUFD#PBF 功能描述:IC CONV DDR DDR2 DDR3 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器,Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN(7x7) 包装:管件
LTC3634EUFD#TRPBF 功能描述:IC CONV DDR DDR2 DDR3 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器,Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN(7x7) 包装:管件
LTC3634HFE#PBF 制造商:Linear Technology 功能描述:IC CONV DDR DDR2 DDR3 28TSSOP 制造商:Linear Technology 功能描述:BUCK 15V 3A 500KHZ-4MHZ TS 制造商:Linear Technology 功能描述:DP-SWREG/Monolithic, 15V Dual 3A Monolithic Step Down Regulator for DDR Power 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, TSSOP-28, Primary Input Voltage:15V, No. of Outputs:2, Output Current:3A, No. of Pins:28, Operating Temperature Min:-40C, Operating Temperature Max:150C, MSL:MSL 1 - Unlimited, Package / Case:28-TSSOP , RoHS Compliant: Yes