- 您现在的位置：买卖IC网 > PDF目录15286 > LTC3732CUHF#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 38-QFN PDF资料下载
参数资料
| 型号： | LTC3732CUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 38-QFN |
| 标准包装： | 52 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 750kHz |
| 占空比： | 98.5% |
| 电源电压： | 4.5 V ~ 7 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3732
APPLICATIO S I FOR ATIO
tions having a highly varying input voltage, additional
phases will produce the best results.
Accepting larger values of ? I L allows the use of low
inductances but can result in higher output voltage ripple.
A reasonable starting point for setting ripple current is
? I L = 0.4(I OUT )/N, where N is the number of channels and
I OUT is the total load current. Remember, the maximum
? I L occurs at the maximum input voltage. The individual
inductor ripple currents are constant determined by the
inductor, input and output voltages.
inductor ripple current and consequent output voltage
ripple. Do not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive than
ferrite. A reasonable compromise from the same manu-
facturer is Kool M μ . Toroids are very space efficient,
especially when you can use several layers of wire. Be-
cause they lack a bobbin, mounting is more difficult.
However, designs for surface mount are available which
do not increase the height significantly.
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
1-PHASE
2-PHASE
3-PHASE
4-PHASE
6-PHASE
Power MOSFET and D1, D2, D3 Selection
At least two external power MOSFETs must be selected for
each of the three output sections: One N-channel MOSFET
for the top (main) switch and one or more N-channel
MOSFET(s) for the bottom (synchronous) switch. The
number, type and “on” resistance of all MOSFETs selected
take into account the voltage step-down ratio as well as the
actual position (main or synchronous) in which the MOSFET
will be used. A much smaller and much lower input
0
0.1
0.2
0.3 0.4 0.5 0.6 0.7
DUTY FACTOR (V OUT /V IN )
0.8
0.9
capacitance MOSFET should be used for the top MOSFET
in applications that have an output voltage that is less than
3732 F04
Figure 4. Normalized Peak Output Current
vs Duty Factor [I RMS = 0.3(I O(P-P) ]
Inductor Core Selection
Once the value for L1 to L3 is determined, the type of
inductor must be selected. High efficiency converters
generally cannot afford the core loss found in low cost
powdered iron cores, forcing the use of ferrite,
molypermalloy or Kool M μ ? cores. Actual core loss is
independent of core size for a fixed inductor value, but it
is very dependent on inductance selected. As inductance
increases, core losses go down. Unfortunately, increased
inductance requires more turns of wire and therefore
copper losses will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can
concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design
1/3 of the input voltage. In applications where V IN >> V OUT ,
the top MOSFETs’ “on” resistance is normally less impor-
tant for overall efficiency than its input capacitance at
operating frequencies above 300kHz. MOSFET manufac-
turers have designed special purpose devices that provide
reasonably low “on” resistance with significantly reduced
input capacitance for the main switch application in switch-
ing regulators.
The peak-to-peak MOSFET gate drive levels are set by the
voltage, V CC , requiring the use of logic-level threshold
MOSFETs in most applications. Pay close attention to the
BV DSS specification for the MOSFETs as well; many of the
logic-level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the “on”
resistance R DS(ON) , input capacitance, input voltage and
maximum output current.
MOSFET input capacitance is a combination of several
components but can be taken from the typical “gate
charge” curve included on most data sheets (Figure 5).
current is exceeded. This results in an abrupt increase in
Kool M μ is a registered trademark of Magnetics, Inc.
3732f
13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1735IGN#TR | IC REG CTRLR BUCK PWM CM 16-SSOP |
| VI-B2Z-EY-F4 | CONVERTER MOD DC/DC 2V 20W |
| LTC3810HUH-5#TRPBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3834EUFD#TRPBF | IC REG CTRLR BUCK PWM CM 20-QFN |
| LTC3834EFE#TRPBF | IC REG CTRLR BUCK PWM CM 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3733CG | 功能描述:IC CTRLR BUCK AMD 3PHASE 36-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3733CG#PBF | 功能描述:IC CTRLR BUCK AMD 3PHASE 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3733CG#TR | 功能描述:IC CTRLR BUCK 3PH AMD CPU 36SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3733CG#TRPBF | 功能描述:IC CTRLR BUCK AMD 3PHASE 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3733CUHF-1 | 功能描述:IC CTRLR BUCK 3PH AMD CPU 38-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。