- 您现在的位置：买卖IC网 > PDF目录98003 > LTC3773EUHF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC38 PDF资料下载
参数资料
| 型号： | LTC3773EUHF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PQCC38 |
| 封装： | 5 X 7 MM, PLASTIC, MO-220WHKD, QFN-38 |
| 文件页数： | 2/32页 |
| 文件大小： | 461K |
| 代理商： | LTC3773EUHF |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC3773
10
3773fa
SENSE1+ (Pin 1/Pin 34): The (+) Input to the Channel 1
Differential Current Comparator. The ITH1 pin voltage and
controlled offsets between the SENSE1– and SENSE1+
pins in conjunction with RSENSE set the channel 1 current
trip threshold.
SENSE1– (Pin 2/Pin 35): The (–) Input to the Channel 1
Differential Current Comparator.
SDB/SDB1, SDB2, SDB3 (Pin 3/Pins 36, 37, 38): Shut-
down, Active Low. For G package, SDB1, SDB2 and SDB3
are shorted at the SDB pin. The power up thresholds for
channel 1, 2 and 3 are set at 1.2V, 1.8V and 2.4V respec-
tively. By pulling the SDB1, SDB2 and SDB3 pins below
0.4V, the IC is put into low current shutdown mode (IVCCQ
<30A). There is a 0.5A pull-up current at each SDB pin.
An external capacitor can be added at this pin to provide
power up delay.
TRACK1 (Pin 4/Pin 1): Channel 1 Tracking Input. TRACK1
is used for tracking multiple LTC3773s. See the Startup
Tracking application. To disable this feature, oat this pin
or tie it to VCC. TRACK1 provides a 1A pull-up current.
An external capacitor can be added at this pin to provide
soft-start. During startup or output short-circuit condition,
if the potential at TRACK1 is less than 0.54V, current limit
foldback is disabled. When channel 1 is powered down,
this pin will be pulled low.
VFB1 (Pin 5/Pin 2): Channel 1 Error Amplier Feedback
Input. This pin connects the error amplier input to an
external resistive divider from VOUT1.
ITH1 (Pin 6/Pin 3): Channel 1 Error Amplier Output and
Switching Regulator Compensation Point. The current
comparator’s threshold increases with this control volt-
age.
SGND (Pin 7/Pin 4): Signal Ground. This pin must be
routed separately under the IC to the PGND pin and then
to the main ground plane.
ITH2 (Pin 8/Pin 5): Channel 2 Error Amplier Output and
Switching Regulator Compensation Point. See ITH1.
ITH3 (Pin 9/Pin 6): Channel 3 Error Amplier Output and
Switching Regulator Compensation Point. See ITH1.
VFB2 (Pin 10/Pin 7): Channel 2 Error Amplier Feedback
Input. See VFB1.
VFB3 (Pin 11/Pin 8): Channel 3 Error Amplier Feedback
Input. See VFB1.
TRACK2 (Pin 12/Pin 9): Channel 2 Tracking Input. Tie the
TRACK2 pin to a resistive divider connected to the output
of channel 1 for either coincident or ratiometric output
tracking. See the Soft-Start/Tracking application. TRACK2
comes with a 1A pull-up current. An external capacitor
can be added at this pin to provide soft-start. During
startup or output short-circuit condition, if the potential
at TRACK2 is less than 0.54V, current limit foldback is
disabled. When channel 2 is powered down, this pin will
be pulled low.
TRACK3 (Pin 13/Pin 10): Channel 3 Tracking Input. See
TRACK2.
SENSE2– (Pin 14/Pin 11): The (–) Input to the Channel 2
Differential Current Comparator. See SENSE1–.
SENSE2+ (Pin 15/Pin 12): The (+) Input to the Channel 2
Differential Current Comparator. See SENSE1+.
SENSE3– (Pin 16/Pin 13): The (–) Input to the Channel 3
Differential Current Comparator. See SENSE1–.
SENSE3+ (Pin 17/Pin 14): The (+) Input to the Channel 3
Differential Current Comparator. See SENSE1+.
VCC (Pin 18/Pin 15): Main Input Supply. All internal circuits
except the output drivers are powered from this pin. VCC
should be connected to a low noise 5V power supply and
should be bypassed to SGND with at least a 1F capacitor
in close proximity to the LTC3773.
PLLFLTR (Pin 19/Pin 16): Phase-Locked Loop Lowpass
Filter. The phase-locked loop’s lowpass lter is tied to this
pin. Alternatively, when external frequency synchronizing
is not used, this pin can be forced low, left oating or tied
high to vary the frequency of the internal oscillator.
PIN FUNCTIONS (G/UHF)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3773EG | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO36 |
| LTC3801ES6#PBF | 1 A SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3803ES6-3 | 1 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3803IS6-3 | 1 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO6 |
| LTC3805HMSE-5#TRPBF | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3773EUHF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3773EUHF#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3774EUHE#PBF | 制造商:Linear Technology 功能描述:SWITCHING REG, BUCK, ADJ, 2.2MHZ, DFN-36 |
| LTC3774IUHE#PBF | 制造商:Linear Technology 功能描述:SWITCHING REG, BUCK, ADJ, 2.2MHZ, DFN-36 |
| LTC3775EMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。