- 您现在的位置：买卖IC网 > PDF目录15338 > LTC3775EUD#PBF (Linear Technology)IC REG CTRLR BUCK PWM VM 16-QFN PDF资料下载
参数资料
| 型号： | LTC3775EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/34页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 16-QFN |
| 标准包装： | 121 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 80% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC3775
APPLICATIONS INFORMATION
Δ I L may be calculated using the equation:
current. Lower ripple current reduces core losses in the
1 – OUT
I L =
V OUT
L ? f SW
V
V IN
inductor, ESR losses in the output capacitors and out-
put voltage ripple. Highest ef?ciency is obtained at low
frequency with small ripple current. However, achieving
Since Δ I L increases with input voltage, the output ripple
voltage is highest at maximum input voltage. Typically,
once the ESR requirement is satis?ed, the capacitance is
adequate for ?ltering and has the necessary RMS current
rating.
high ef?ciency requires a large inductor and generates
higher output voltage excursion during load transients.
There is a trade-off between component size, ef?ciency
and operating frequency. Given a speci?ed limit for ripple
current, the inductor value can be obtained using the fol-
lowing equation:
Manufacturers such as Sanyo, Panasonic and Cornell
Dublilier should be considered for high performance
through-hole capacitors. The OS-CON semiconductor
L =
V OUT
f SW ? I L(MAX)
? 1–
V OUT
V IN(MAX)
electrolyte capacitor available from Sanyo has a good
(ESR)(size) product. An additional ceramic capacitor in
parallel with OS-CON capacitors is recommended to offset
the effect of lead inductance.
In surface mount applications, multiple capacitors may
have to be connected in parallel to meet the ESR or tran-
sient current handling requirements of the application.
Aluminum electrolytic and dry tantalum capacitors are
both available in surface mount con?gurations. New special
polymer surface mount capacitors offer very low ESR also
but have much lower capacitive density per unit volume.
In the case of tantalum, it is critical that the capacitors are
surge tested for use in switching power supplies. Several
excellent output capacitor choices are the Sanyo POSCAP
TPD, POSCAP TPB, AVX TPS, AVX TPSV, the Kemet T510
Once the value for L is known, the type of inductor must
be selected. High ef?ciency converters generally cannot
afford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy or
Kool Mμ ? cores. A variety of inductors designed for high
current, low voltage applications are available from manu-
facturers such as Sumida, Panasonic, Coiltronics, Coilcraft
and Toko. See the Current Limit Programming section for
calculation of the inductor saturation current.
Current Limit Programming
If current sensing is implemented with a sense resistor,
the topside current limit can be programmed by setting
R ILIMT as follows:
series of surface mount tantalums, Kemet AO-CAPs or the
Panasonic SP series of surface mount special polymer
capacitors available in case heights ranging from 2mm
R ILIMT = CF ? R SENSE ?
I O(MAX) + 0.5 ? I L
I LIMIT(MIN)
to 4mm. Other capacitor types include Nichicon PL series
and Sprague 595D series. Consult the manufacturer for
other speci?c recommendations.
Inductor Selection
The inductor in a typical LTC3775 application circuit is
chosen based on the required ripple current, its size and
its saturation current rating. The inductor should not be al-
lowed to saturate below the hard current limit threshold.
The inductor value sets the ripple current, which is com-
monly chosen at around 40% of the anticipated full load
where:
R SENSE = Sense resistor value
I O(MAX) = Maximum output current
Δ I L = Inductor ripple current (refer to the Output Capaci-
tor Selection section).
I LIMT(MIN) = I LIMT pin minimum pull-down current of
90μA
CF = Correction factor to provide safety margin and
account for R SENSE tolerance; use a value of CF = 1.2
is reasonable.
3775fa
22
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2196YM TR | IC REG CTRLR BST FLYBK PWM 8SOIC |
| RCC26DRTN-S93 | CONN EDGECARD 52POS DIP .100 SLD |
| SLP682M016A1P3 | CAP ALUM 6800UF 16V 20% SNAP |
| VE-JWP-EW-F1 | CONVERTER MOD DC/DC 13.8V 100W |
| RCC26DRTH-S93 | CONN EDGECARD 52POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3775IMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3775IMSE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM VM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3775IUD#PBF | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3775IUD#TRPBF | 功能描述:IC REG CTRLR BUCK PWM VM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3776EGN | 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Sync Step Down 2.75V to 9.8V Input 24-Pin SSOP N |
发布紧急采购，3分钟左右您将得到回复。