- 您现在的位置：买卖IC网 > PDF目录44992 > LTC3785EUF (LINEAR TECHNOLOGY CORP) 3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 PDF资料下载
参数资料
| 型号： | LTC3785EUF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC24 |
| 封装： | 4 X 4 MM, PLASTIC, MO-220WGGD, QFN-24 |
| 文件页数： | 2/20页 |
| 文件大小： | 275K |
| 代理商： | LTC3785EUF |
LTC3785
0
3785fc
operaTion
switch A and D. In most applications a 0.1F to 0.47F,
X5R or X7R dielectric capacitor is adequate.
RUN/SOFT-START (RUN/SS)
The RUN/SS pin serves as the enable to the LTC3785,
soft-start function, and fault programming. A 1A current
source charges the external capacitor. Once the RUN/SS
voltageisaboveadiodedrop(~0.7V)theICisenabled.Once
the IC is enabled, the RUN/SS voltage minus a diode drop
(RUN/SS – 0.7V) clamps the output of the error amp (VC)
to limit duty cycle. The range of the duty cycle clamping is
approximately 0.7V to 1.7V. The RUN/SS pin is clamped
to approximately 2.2V. If current limit is reached the pin
will begin to discharge with a current determined by the
magnitude of inductor current overcurrent limit, but not
to exceed 10A. This function will be described in more
detail in the Forward Current Limit section.
OSCILLATOR
The frequency of operation is set through a resistor from
the RT pin to ground where:
f
R
MHz
OSC
T
25000
ERROR AMP
The error amplifier is a voltage mode amplifier with a
reference voltage of 1.225V internally connected to the
non-inverting input. The loop compensation components
are configured around the amplifier to provide loop com-
pensation for the converter. The RUN/SS pin will clamp the
error amp output, VC, to provide a soft-start function.
UNDERVOLTAGE AND OVERVOLTAGE PROTECTION
The LTC3785 incorporates overvoltage (OV) and
undervoltage (UV) functions for fault protection and
transient limitation. Both comparators are connected
to the VSENSE pin, which usually has a similar voltage
divider as the error amplifier without the compensation.
The overvoltage threshold is 10% above the reference.
The undervoltage threshold is 6.5% below the reference
with both comparators having 1.5% hysteresis. During
an overvoltage fault, all output switching stops until the
fault ceases. During an undervoltage fault, the IC is com-
manded to run fixed frequency only (disabled Burst Mode
operation). If the design requires a tightened threshold to
one of the comparator thresholds the voltage divider on
the VSENSE pin can be skewed to achieve the threshold.
Since the range is a constant, tightening the UV threshold
will loosen the OV threshold and vice versa.
FORWARD CURRENT LIMIT
TheLTC3785isdesignedtosensetheinputcurrentbysam-
plingthevoltageacrossMOSFETAduringtheontimeofthe
switch (TG1 = High). The sense pins are ISVIN and ISSW1. A
current sense resistor can be used if increased accuracy is
required. The current limit threshold can be programmed
with a resistor on the ILSET pin. Once the desired current
limit has been chosen, RILSET can be determined by the
following formula:
RILSET =
6000
RDS(ON)A ILIMIT
Ω
where RDS(ON)A = RDS(ON) of N-channel MOSFET switch A
and ILIMIT = current limit in Amps.
Once the voltage between ISVIN and ISSW1 exceeds the
threshold, current will be sourced out of FB to take control
of the voltage loop, resulting in a lower output voltage
to regulate the input current. This fault condition causes
the RUN/SS capacitor to begin discharging. The level of
the discharge current depends on how much the current
exceeds the programmed threshold. Figure 3 is a simpli-
fied diagram of the current sense and fault circuitry. If the
current limit fault duration is long enough to discharge the
RUN/SS capacitor below 1.225V, the fault latch is set and
will cycle the RUN/SS capacitor 16 times (1A charging
and 1A discharging of the RUN/SS capacitor) to create an
off time of 32 times the soft-start time before the outputs
are allowed to switch to restart the output voltage. If the
current limit fault level exceeds 150% of the programmed
ILIMIT level at any time, the IMAX comparator is tripped and
output switches B and D are turned on to discharge the
inductor current for the remainder of the cycle.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3786IMSE#TRPBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EMSE#TRPBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EMSE#PBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3786EUD#PBF | SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PQCC16 |
| LTC3787IGN#TRPBF | SWITCHING CONTROLLER, 585 kHz SWITCHING FREQ-MAX, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3785EUF#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3785EUF#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3785EUFPBF | 制造商:Linear Technology 功能描述:10V Synch Buck-Boost Controller LTC3785 |
发布紧急采购，3分钟左右您将得到回复。