- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3801BES6#TRM (Linear Technology)IC REG CTRLR BUCK PWM TSOT23-6 PDF资料下载
参数资料
| 型号： | LTC3801BES6#TRM |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM TSOT23-6 |
| 标准包装： | 500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 650kHz |
| 占空比： | 100% |
| 电源电压： | 2.4 V ~ 9.8 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC3801BES6 LTC3801BES6-ND |
LTC3801/LTC3801B
APPLICATIO S I FOR ATIO
I RIPPLE ≤
V IN ? V OUT ? V OUT + V D ?
? 0 . 03 ? ? V IN + V D ?
? R SENSE ?
R DS ( ON ) DC = 100 % =
R DS ( ON ) ?
I RIPPLE =0.4(I OUT(MAX) ).Remember,themaximumI RIPPLE
occurs at the maximum input voltage.
In Burst Mode operation on the LTC3801, the ripple
current is normally set such that the inductor current is
continuous during the burst periods. Therefore, the peak-
to-peak ripple current must not exceed:
0 . 03
R SENSE
This implies a minimum inductance of:
L MIN = ? ?
f ? ?
(Use V IN(MAX) = V IN )
A smaller value than L MIN could be used in the circuit;
however, the inductor current will not be continuous
during burst periods.
Inductor Core Selection
Once the value for L is known, the type of inductor must be
selected. High efficiency converters generally cannot af-
ford the core loss found in low cost powdered iron cores,
forcing the use of more expensive ferrite, molypermalloy
or Kool M μ ? cores. Actual core loss is independent of core
size for a fixed inductor value, but it is very dependent on
inductance selected. As inductance increases, core losses
go down. Unfortunately, increased inductance requires
more turns of wire and therefore copper losses will in-
crease. Ferrite designs have very low core losses and are
preferred at high switching frequencies, so design goals
can concentrate on copper loss and preventing saturation.
Ferrite core material saturates “hard,” which means that
inductance collapses abruptly when the peak design cur-
rent is exceeded. This results in an abrupt increase in
inductor ripple current and consequent output voltage
ripple. Do not allow the core to saturate!
Molypermalloy (from Magnetics, Inc.) is a very good, low
loss core material for toroids, but it is more expensive
manufacturer is Kool M μ . Toroids are very space efficient,
especially when you can use several layers of wire.
Because they generally lack a bobbin, mounting is more
difficult. However, new designs for surface mount that do
not increase the height significantly are available.
Power MOSFET Selection
An external P-channel power MOSFET must be selected
for use with the LTC3801/LTC3801B. The main selection
criteria for the power MOSFET are the threshold voltage
V GS(TH) and the “on” resistance R DS(ON) , reverse transfer
capacitance C RSS and total gate charge.
Since the LTC3801/LTC3801B are designed for operation
down to low input voltages, a sublogic level threshold
MOSFET (R DS(ON) guaranteed at V GS = 2.5V) is required
for applications that work close to this voltage. When
these MOSFETs are used, make sure that the input supply
to the LTC3801/LTC3801B is less than the absolute maxi-
mum V GS rating, typically 8V.
The required minimum R DS(ON) of the MOSFET is governed
by its allowable power dissipation. For applications that may
operate the LTC3801/LTC3801B in dropout, i.e., 100% duty
cycle, at its worst case the required R DS(ON) is given by:
P P
( I OUT ( MAX ) ) 2 ( 1 + δ p )
where P P is the allowable power dissipation and δ p is the
temperature dependency of R DS(ON) . (1 + δ p) is generally
given for a MOSFET in the form of a normalized R DS(ON) vs
temperature curve, but δ p = 0.005/ ° C can be used as an
approximation for low voltage MOSFETs.
In applications where the maximum duty cycle is less than
100% and the LTC3801/LTC3801B are in continuous
mode, the R DS(ON) is governed by:
P P
( DC ) I OUT 2 ( 1 + δ p )
where DC is the maximum operating duty cycle of the
LTC3801/LTC3801B.
than ferrite. A reasonable compromise from the same
Kool M μ is a registered trademark of Magnetics, Inc.
sn3801 3801fs
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3802EGN | IC REG CTRLR BUCK PWM VM 28-SSOP |
| LTC3803MPS6-3#TRMPBF | IC REG CTRLR FLYBK PWM TSOT23-6 |
| LTC3803MPS6-5#TRMPBF | IC REG CTRLR FLYBK PWM TSOT23-6 |
| LTC3803MPS6#TRMPBF | IC REG CTRLR FLYBK PWM TSOT23-6 |
| LTC3805HMSE-5#PBF | IC REG CTRLR BST FLYBK CM 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3801ES6#TR | 功能描述:IC REG CTRLR BUCK PWM TSOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3801ES6#TRM | 功能描述:IC REG CTRLR BUCK PWM TSOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3801ES6#TRMPBF | 功能描述:IC REG CTRLR BUCK PWM TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3801ES6#TRPBF | 功能描述:IC REG CTRLR BUCK PWM TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3802EGN | 功能描述:IC REG CTRLR BUCK PWM VM 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。