参数资料
型号: LTC3810HUH-5#PBF
厂商: Linear Technology
文件页数: 23/38页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 32-QFN
标准包装: 73
PWM 型: 电流模式
输出数: 1
频率 - 最大: 1MHz
占空比: 99%
电源电压: 4.35 V ~ 60 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 150°C
封装/外壳: 32-WFQFN 裸露焊盘
包装: 管件
LTC3810-5
APPLICATIONS INFORMATION
takes over before the INTV CC capacitor discharges below
the UV threshold. When the EXTV CC regulator is active,
the EXTV CC pin can supply up to 50mA RMS. Do not ap-
ply more than 15V to the EXTV CC pin. The following list
summarizes the possible connections for EXTV CC :
1. EXTV CC grounded. This connection will require INTV CC
to be powered continuously from an external NMOS
from V IN resulting in an efficiency penalty as high as
10% at high input voltages.
2. EXTV CC connected directly to V OUT . This is the normal
connection for 4.7V < V OUT < 15V and provides the
highest efficiency. The power supply will start up using
an external NMOS or a bleed resistor until the output
supply is available.
3. EXTV CC connected to an output-derived boost network.
If V OUT < 4.7V. The low voltage output can be boosted
using a charge pump or flyback winding to greater
than 4.7V.
4. EXTV CC connected to INTV CC . This is the required con-
nection for EXTV CC if INTV CC is connected to an external
supply where the external supply is 4.5V < V EXT < 15V.
Applications using large MOSFETs with a high input
voltage and high frequency of operation may result in a
large EXTV CC pin current. Due to the LTC3810-5 thermally
enhanced package, maximum junction temperature will
rarely be exceeded, however, it is good design practice
to verify that the maximum junction temperature rating
and RMS current rating are within the maximum limits.
Typically, most of the EXTV CC current consists of the
MOSFET gates current. In continuous mode operation,
this EXTV CC current is:
I EXTVCC = f ( Q G(TOP) + Q G(BOTTOM) ) + 3mA < 50mA
The junction temperature can be estimated from the
equations given in Note 2 of the Electrical Characteristics
as follows:
T J = T A + I EXTVCC ? (V EXTVCC – V INTVCC )(34°C/W)
The calculated T J should be <125°C for E- and I-grade
or < 150°C for H-grade. If absolute maximum ratings are
exceeded, consider using an external supply connected
directly to the INTV CC pin.
FEEDBACK LOOP/COMPENSATION
Feedback Loop Types
In a typical LTC3810-5 circuit, the feedback loop con-
sists of the modulator, the output filter and load, and the
feedback amplifier with its compensation network. All of
these components affect loop behavior and must be ac-
counted for in the loop compensation. The modulator and
output filter consists of the internal current comparator,
the output MOSFET drivers and the external MOSFETs,
inductor and output capacitor. Current mode control
eliminates the effect of the inductor by moving it to the
inner loop, reducing it to a first order system. From a
feedback loop point of view, it looks like a linear voltage
controlled current source from I TH to V OUT and has a gain
equal to (I MAX R OUT )/1.2V. It has fairly benign AC behavior
at typical loop compensation frequencies with significant
phase shift appearing at half the switching frequency. The
external output capacitor and load cause a first order roll
off at the output at the R OUT C OUT pole frequency, with
the attendant 90° phase shift. This roll off is what filters
the PWM waveform, resulting in the desired DC output
voltage. The output capacitor also contributes a zero at
the C OUT R ESR frequency which adds back the 90° phase
and cancels the first order roll off.
So far, the AC response of the loop is pretty well out of the
user’s control. The modulator is a fundamental piece of
the LTC3810-5 design and the external output capacitor is
usually chosen based on the regulation and load current
requirements without considering the AC loop response.
The feedback amplifier, on the other hand, gives us a
handle with which to adjust the AC response. The goal is
to have 180° phase shift at DC (so the loop regulates), and
something less than 360° phase shift (preferably about
300°) at the point that the loop gain falls to 0dB, i.e., the
crossover frequency, with as much gain as possible at
frequencies below the crossover frequency. Since the
modulator/output filter is a first order system with maxi-
mum of 90° phase shift (at frequencies below f SW /4) and
the feedback amplifier adds another 90° of phase shift,
some phase boost is required at the crossover frequency
to achieve good phase margin. If the ESR zero is below the
crossover frequency, this zero may provide enough phase
boost to achieve the desired phase margin and the only
38105fd
23
相关PDF资料
PDF描述
LTC3834EUFD#PBF IC REG CTRLR BUCK PWM CM 20-QFN
RLB9012-152KL INDUCTOR HI CURRNT RADIAL 1500UH
RBA32DCBD CONN EDGECARD 64POS R/A .125 SLD
LTC1929CG-PG#PBF IC REG CTRLR BUCK PWM CM 28-SSOP
RBA32DCBH CONN EDGECARD 64POS R/A .125 SLD
相关代理商/技术参数
参数描述
LTC3810IG 制造商:Linear Technology 功能描述:
LTC3810IG#PBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3810IG#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3810IUH-5#PBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)
LTC3810IUH-5#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR)