参数资料
型号: LTC3828
厂商: Linear Technology Corporation
英文描述: 16-Bit Bus Transceiver With 3-State Outputs 48-SSOP -40 to 85
中文描述: 双2相降压型跟踪控制器
文件页数: 10/32页
文件大小: 396K
代理商: LTC3828
10
LTC3828
3828f
(Refer to Functional Diagram)
OPERATIOU
Main Control Loop
The IC uses a constant frequency, current mode step-
down architecture with the two controller channels oper-
ating 180 degrees out of phase. During normal operation,
each top MOSFET is turned on when the clock for that
channel sets the RS latch, and turned off when the main
current comparator, I
1
, resets the RS latch. The peak
inductor current at which I
1
resets the RS latch is con-
trolled by the voltage on the I
TH
pin, which is the output of
each error amplifier EA. The V
OSENSE
pin receives the
voltage feedback signal, which is compared to the internal
reference voltage by the EA. When the load current in-
creases, it causes a slight decrease in V
OSENSE
relative to
the 0.8V reference, which in turn causes the I
TH
voltage to
increase until the average inductor current matches the
new load current. After the top MOSFET has turned off, the
bottom MOSFET is turned on until either the inductor
current starts to reverse, as indicated by current compara-
tor I
2
, or the beginning of the next cycle.
The top MOSFET drivers are biased from floating boot-
strap capacitor C
B
, which normally is recharged during
each off cycle through an external diode when the top
MOSFET turns off. As V
IN
decreases to a voltage close to
V
OUT
, the loop may enter dropout and attempt to turn on
the top MOSFET continuously. The dropout detector de-
tects this and forces the top MOSFET off for about 400ns
every tenth cycle to allow C
B
to recharge.
The main control loop is shut down by pulling the RUN pin
low. When the RUN pin reaches 1.5V, the main control
loop is enabled. When RUN1 is low, all controller functions
are shut down, including the 5V regulator.
Low Current Operation
The FCB/PLLIN pin is a multifunction pin providing two
functions: 1) to accept external clock signal; and 2) to
select among three modes of light load operations. When
the FCB/PLLIN pin voltage is below 0.8V, the controller
forces continuous PWM current mode operation. In this
mode, the top and bottom MOSFETs are alternately
turned on to maintain the output voltage independent of
direction of inductor current. When the FCB/PLLIN pin is
below V
INTVCC
– 2V but greater than 0.8V, the controller
enters Burst Mode operation. Burst Mode operation sets
a minimum output current level before inhibiting the top
switch and turns off the synchronous MOSFET(s) when
the inductor current goes negative. This combination of
requirements will, at low currents, force the I
TH
pin below
a voltage threshold that will temporarily inhibit turn-on of
both output MOSFETs until the output voltage drops.
There is 60mV of hysteresis in the burst comparator B
tied to the I
TH
pin. This hysteresis produces output
signals to the MOSFETs that turn them on for several
cycles, followed by a variable “sleep” interval depending
upon the load current. The resultant output voltage ripple
is held to a very small value by having the hysteretic
comparator after the error amplifier gain block. When the
FCB/PLLIN pin voltage is above 4.8V, the controller
operates in constant frequency mode and the synchro-
nous MOSFET is turned off when inductor current nears
zero in each cycle.
In order to prevent erratic operation if no external connec-
tions are made to the FCB/PLLIN pin, the FCB/PLLIN pin
has a 0.18
μ
A internal current source pulling the pin high.
The following table summarizes the possible states avail-
able on the FCB/PLLIN pin:
Table 1
FCB/PLLIN Pin
0V to 0.75V
Condition
Forced Continuous Both Controllers
(Current Reversal Allowed—
Burst Inhibited)
Minimum Peak Current Induces
Burst Mode Operation
No Current Reversal Allowed
Burst Mode Operation Disabled
Constant Frequency Mode Enabled
No Current Reversal Allowed
No Minimum Peak Current
0.85V < V
FCB/PLLIN
< 4.3V
>4.8V
Besides providing a logic input to force continuous
operation, the FCB/PLLIN pin acts as the input for exter-
nal clock synchronization. Upon detecting the presence
of an external clock signal, channel 1 will lock on to this
external clock and this will be followed by channel 2 (see
Frequency Synchronization section). The LTC3828 de-
faults to forced continuous mode when sychronized to an
external clock.
相关PDF资料
PDF描述
LTC486 Quad Low Power RS485 Driver
LTC486C ; LED Color:Red; Luminous Intensity:63mcd; Viewing Angle:80 ; Forward Current:20mA; Forward Voltage:2.1V; Operating Temperature Range:-40 C to +100 C RoHS Compliant: Yes
LTC486CN Quad Low Power RS485 Driver
LTC486CS Quad Low Power RS485 Driver
LTC486I Quad Low Power RS485 Driver
相关代理商/技术参数
参数描述
LTC3828EG#PBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP(0.173",4.40mm 宽) 包装:带卷 (TR)
LTC3828EG#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3828EUH 制造商:Linear Technology 功能描述:DC DC Cntrlr Dual-OUT Sync Step Down 4.5V to 28V Input 32-Pin QFN EP
LTC3828EUH#PBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3828EUH#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX