- 您现在的位置：买卖IC网 > PDF目录44994 > LTC3851AEMSE#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PDSO16 PDF资料下载
参数资料
| 型号： | LTC3851AEMSE#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PDSO16 |
| 封装： | LEAD FREE, PLASTIC, MSOP-16 |
| 文件页数： | 3/30页 |
| 文件大小： | 430K |
| 代理商： | LTC3851AEMSE#PBF |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3851A
11
3851afa
operaTion
the error amplifier, EA, will decrease the voltage on the ITH
pin. When the ITH voltage drops below 0.4V, the internal
sleep signal goes high (enabling sleep mode) and both
external MOSFETs are turned off.
In sleep mode, the load current is supplied by the output
capacitor. As the output voltage decreases, the EA’s output
begins to rise. When the output voltage drops enough, the
sleep signal goes low, and the controller resumes normal
operation by turning on the top external MOSFET on the
next cycle of the internal oscillator. When a controller is
enabled for Burst Mode operation, the inductor current is
not allowed to reverse. The reverse current comparator,
IREV, turns off the bottom external MOSFET just before the
inductor current reaches zero, preventing it from revers-
ing and going negative. Thus, the controller operates in
discontinuous operation. In forced continuous operation,
the inductor current is allowed to reverse at light loads or
under large transient conditions. The peak inductor cur-
rent is determined by the voltage on the ITH pin, just as in
normal operation. In this mode the efficiency at light loads
is lower than in Burst Mode operation. However, continu-
ous mode has the advantages of lower output ripple and
less interference to audio circuitry.
When the MODE/PLLIN pin is connected to GND, the
LTC3851A operates in PWM pulse-skipping mode at light
loads.Atverylightloadsthecurrentcomparator,ICMP,may
remain tripped for several cycles and force the external top
MOSFET to stay off for the same number of cycles (i.e.,
skipping pulses). The inductor current is not allowed to
reverse (discontinuous operation). This mode, like forced
continuous operation, exhibits low output ripple as well as
low audio noise and reduced RF interference as compared
to Burst Mode operation. It provides higher low current
efficiency than forced continuous mode, but not nearly as
high as Burst Mode operation.
Frequency Selection and Phase-Locked Loop
(FREQ/PLLFLTR and MODE/PLLIN Pins)
Theselectionofswitchingfrequencyisatrade-offbetween
efficiency and component size. Low frequency opera-
tion increases efficiency by reducing MOSFET switching
losses, but requires larger inductance and/or capacitance
to maintain low output ripple voltage. The switching fre-
quency of the LTC3851A can be selected using the FREQ/
PLLFLTR pin. If the MODE/PLLIN pin is not being driven
by an external clock source, the FREQ/PLLFLTR pin can
be used to program the controller’s operating frequency
from 250kHz to 750kHz.
A phase-locked loop (PLL) is available on the LTC3851A
to synchronize the internal oscillator to an external clock
source that is connected to the MODE/PLLIN pin. The
controlleroperatesinforcedcontinuousmodeofoperation
when it is synchronized. A series RC should be connected
between the FREQ/PLLFLTR pin and GND to serve as the
PLL’s loop filter. It is suggested that the external clock be
applied before enabling the controller unless a second
resistorisconnectedinparallelwiththeseriesRCnetwork.
Thesecondresistorpreventsverylowswitchingfrequency
operation if the controller is enabled before the clock.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>10%) as well as other more serious con-
ditions that may overvoltage the output. In such cases,
the top MOSFET is turned off and the bottom MOSFET is
turned on until the overvoltage condition is cleared.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3851EUD-1#PBF | 0.05 A SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PQCC16 |
| LTC3851EMSE-1#PBF | 0.05 A SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3851IMSE-1#PBF | 0.05 A SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3851IMSE#TRPBF | 0.05 A SWITCHING CONTROLLER, 790 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC3851IMSE#PBF | 0.05 A SWITCHING CONTROLLER, 790 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3851AEUD#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEUD#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEUD-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AEUD-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851AHMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。