- 您现在的位置：买卖IC网 > PDF目录1832 > LTC3851EMSE-1#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16-MSOP PDF资料下载
参数资料
| 型号： | LTC3851EMSE-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-MSOP |
| 特色产品： | Wide Input Voltage Range Synchronous Step-Down DC/DC Controller |
| 标准包装： | 37 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 790kHz |
| 占空比： | 99% |
| 电源电压： | 4 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 产品目录页面： | 1336 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3851-1
PIN FUNCTIONS
(MSE/UD)
MODE/PLLIN (Pin 1/Pin 15): Forced Continuous Mode,
Burst Mode or Pulse skipping Mode Selection Pin and
External Synchronization Input to Phase Detector Pin.
Connect this pin to INTV CC to force continuous conduction
mode of operation. Connect to GND to enable pulse skipping
mode of operation. To select Burst Mode operation, tie
this pin to INTV CC through a resistor no less than 50k,
but no greater than 250k. A clock on the pin will force the
controller into forced continuous mode of operation and
synchronize the internal oscillator.
FREQ/PLLFLTR (Pin 2/Pin 16): The phase-locked loop’s
lowpass ?lter is tied to this pin. Alternatively, a resistor
can be connected between this pin and GND to vary the
frequency of the internal oscillator.
RUN (Pin 3/Pin 1): Run Control Input. A voltage above
1.25V on this pin turns on the IC. However, forcing this
pin below 1.1V causes the IC to shut down the IC. There
is a 2μA pull-up current on this pin.
TK/SS (Pin 4/Pin 2): Output Voltage Tracking and Soft-Start
Input. A capacitor to ground at this pin sets the ramp rate
for the output voltage. An internal soft-start current of of
1μA charges this capacitor.
I TH (Pin 5/Pin 3): Current Control Threshold and Error
Ampli?er Compensation Point. The current comparator
tripping threshold increases with its I TH control voltage.
FB (Pin 6/Pin 4): Error Ampli?er Feedback Input. This pin
receives the remotely sensed feedback voltage from an
external resistive divider across the output.
SENSE – (Pin 7/Pin 5): Current Sense Comparator Inverting
Input. The (–) input to the current comparator is connected
PGOOD (Pin 9/Pin 7): Power Good Indicator Output. Open-
drain logic out that is pulled to ground when the output
voltage exceeds the ±10% regulation window, after the
internal 17μs power bad mask timer expires.
GND (Pin 10/Pin 8): Ground. All small-signal components
and compensation components should be Kelvin connected
to this ground. The (–) terminal of CV CC and the (–) terminal
of C IN should be closely connected to this pin.
BG (Pin 11/Pin 9): Bottom Gate Driver Output. This pin
drives the gate of the bottom N-channel MOSFET between
GND and INTV CC .
INTV CC (Pin 12/Pin 10): Internal 5V Regulator Output. The
control circuit is powered from this voltage. Decouple this
pin to GND with a minimum 2.2μF low ESR tantalum or
ceramic capacitor.
V IN (Pin 13/Pin 11): Main Input Supply. Decouple this pin
to GND with a capacitor.
BOOST (Pin 14/Pin 12): Boosted Floating Driver Supply.
The (+) terminal of the boost-strap capacitor is connected
to this pin. This pin swings from a diode voltage drop
below INTV CC up to V IN + INTV CC .
TG (Pin 15/Pin 13): Top Gate Driver Output. This is the
output of a ?oating driver with a voltage swing equal to
INTV CC superimposed on the switch node voltage.
SW (Pin 16/Pin 14): Switch Node Connection to the
Inductor. Voltage swing at this pin is from a Schottky diode
(external) voltage drop below ground to V IN .
Exposed Pad (Pin 17): Ground. Must be soldered to PCB,
providing a local ground for the IC.
to the output.
SENSE + (Pin 8/Pin 6): Current Sense Comparator
Noninverting Input. The (+) input to the current comparator
is normally connected to the DCR sensing network or
current sensing resistor.
38511fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3852EUDD#PBF | IC REG CTRLR DOUBLER PWM 24-QFN |
| LTC3853EUJ#PBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LTC3854EMSE#PBF | IC REG CTRLR BUCK PWM CM 12-MSOP |
| LTC3855IUJ#PBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LTC3856IFE#TRPBF | IC REG CTRLR BUCK PWM CM 38TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3851EUD#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3851EUD#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851EUD-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851EUD-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851IGN#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。