- 您现在的位置：买卖IC网 > PDF目录15338 > LTC3851IGN#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 16-SSOP PDF资料下载
参数资料
| 型号： | LTC3851IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 23/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SSOP |
| 产品培训模块： | LTC3851 Single Output DC/DC Switching Regulator Controller |
| 特色产品： | Wide Input Voltage Range Synchronous Step-Down DC/DC Controller |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 790kHz |
| 占空比： | 99% |
| 电源电压： | 4 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页
LTC3851
APPLICATIONS INFORMATION
HIGH CURRENT PATH
3851 F10
CURRENT SENSE
gest noise pick-up at the current or voltage sensing inputs
or inadequate loop compensation. Overcompensation of
the loop can be used to tame a poor PC layout if regulator
bandwidth optimization is not required.
Reduce V IN from its nominal level to verify operation
of the regulator in dropout. Check the operation of the
undervoltage lockout circuit by further lowering V IN while
SENSE + SENSE –
RESISTOR
(R SENSE )
monitoring the outputs to verify operation.
Investigate whether any problems exist only at higher out-
( f ) ( L )
Figure 10. Kelvin Sensing R SENSE
4. Does the (+) terminal of C IN connect to the drain of
the topside MOSFET(s) as closely as possible? This
capacitor provides the AC current to the MOSFET(s).
5. Is the INTV CC decoupling capacitor connected closely
between INTV CC and GND? This capacitor carries the
MOSFET driver peak currents. An additional 1μF ceramic
capacitor placed immediately next to the INTV CC and
GND pins can help improve noise performance.
6. Keep the switching node (SW), top gate node (TG) and
boost node (BOOST) away from sensitive small-signal
nodes, especially from the voltage and current sensing
feedback pins. All of these nodes have very large and
fast moving signals and therefore should be kept on
the “output side” (Pin 9 to Pin 16) of the LTC3851EGN
and occupy minimum PC trace area.
PC Board Layout Debugging
It is helpful to use a DC-50MHz current probe to monitor
the current in the inductor while testing the circuit. Monitor
the output switching node (SW pin) to synchronize the
oscilloscope to the internal oscillator and probe the actual
output voltage as well. Check for proper performance over
the operating voltage and current range expected in the
application. The frequency of operation should be main-
tained over the input voltage range down to dropout and
until the output load drops below the low current opera-
tion threshold—typically 10% of the maximum designed
current level in Burst Mode operation.
The duty cycle percentage should be maintained from cycle
to cycle in a well designed, low noise PCB implementation.
Variation in the duty cycle at a subharmonic rate can sug-
put currents or only at higher input voltages. If problems
coincide with high input voltages and low output currents,
look for capacitive coupling between the BOOST, SW, TG
and possibly BG connections and the sensitive voltage
and current pins. The capacitor placed across the current
sensing pins needs to be placed immediately adjacent to
the pins of the IC. This capacitor helps to minimize the
effects of differential noise injection due to high frequency
capacitive coupling. If problems are encountered with
high current output loading at lower input voltages, look
for inductive coupling between C IN , the Schottky and the
top MOSFET to the sensitive current and voltage sensing
traces. In addition, investigate common ground path
voltage pickup between these components and the GND
pin of the IC.
Design Example
As a design example, assume V IN = 12V (nominal), V IN =
22V (maximum), V OUT = 1.8V, I MAX = 5A, and f = 250kHz.
Refer to Figure 13.
The inductance value is chosen ?rst based on a 30%
ripple current assumption. The highest value of ripple
current occurs at the maximum input voltage. Connect a
160k resistor between the FREQ/PLLFLTR and GND pins,
generating 250kHz operation. The minimum inductance
for 30% ripple current is:
1 ? V ?
Δ I L = V OUT ? 1 ? OUT ?
? V IN ?
A 4.7μH inductor will produce 28% ripple current and
a 3.3μH will result in 40%. The peak inductor current
will be the maximum DC value plus one-half the ripple
current, or 6A, for the 3.3μH value. Increasing the ripple
3851fb
23
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2W1-EW-F2 | CONVERTER MOD DC/DC 12V 100W |
| EBA43DTAH | CONN EDGECARD 86POS R/A .125 SLD |
| EBA43DTAD | CONN EDGECARD 86POS R/A .125 SLD |
| VE-JWP-EW-F4 | CONVERTER MOD DC/DC 13.8V 100W |
| UPM1H331MHD6 | CAP ALUM 330UF 50V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3851IMSE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851IMSE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851IMSE-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851IMSE-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3851IUD#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。