- 您现在的位置：买卖IC网 > PDF目录4962 > LTC3853EUJ#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 40-QFN PDF资料下载
参数资料
| 型号： | LTC3853EUJ#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 40-QFN |
| 产品培训模块： | LTC3853 Multiphase Switching Controller |
| 标准包装： | 2,000 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 3 |
| 频率 - 最大： | 830kHz |
| 占空比： | 98% |
| 电源电压： | 4.5 V ~ 24 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC3853
APPLICATIONS INFORMATION
?V SENSE =
V IN – V OUT V OUT
R D =
R1|| R2 =
R1 =
; R2 =
( V IN(MAX) ? V OUT ) ? V OUT
P LOSS R1 =
V OUT ? V IN – V OUT ?
V IN ? ? f OSC ? L ? ?
? OUT
V IN – V OUT V
To ensure that the application will deliver full load cur-
rent over the full operating temperature range, choose
the minimum value for the Maximum Current Sense
Threshold (V SENSE(MAX) ) in the Electrical Characteristics
table (22mV, 42mV, or 65mV, depending on the state of
the I LIM pin).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given
at 20°C. Increase this value to account for the tempera-
ture coefficient of resistance, which is approximately
0.4%/°C. A conservative value for T L(MAX) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value, use the divider ratio:
R SENSE(EQUIV)
DCR (MAX) at T L(MAX)
C1 is usually selected to be in the range of 0.047μF to
0.47μF. This forces R1||R2 to around 2kΩ, reducing error
that might have been caused by the SENSE pins’ ±1μA
current.
The equivalent resistance R1||R2 is scaled to the room
temperature inductance and maximum DCR:
L
(DCR at 20 ° C) ? C1
The sense resistor values are:
R1|| R2 R1 ? R D
R D 1 ? R D
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at the maximum input
voltage:
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor,
due to the extra switching losses incurred through R1.
16
However, DCR sensing eliminates a sense resistor, reduces
conduction losses and provides higher efficiency at heavy
loads. Peak efficiency is about the same with either method.
To maintain a good signal-to-noise ratio for the current
sense signal, use a minimum D V SENSE of 10mV to 15mV.
For a DCR sensing application, the actual ripple voltage
will be determined by:
?
R1 ? C1 V IN ? f OSC
Slope Compensation and Inductor Peak Current
Slope compensation provides stability in constant-
frequency architectures by preventing subharmonic
oscillations at high duty cycles. It is accomplished
internally by adding a compensating ramp to the inductor
current signal at duty cycles in excess of 40%. Normally,
this results in a reduction of maximum inductor peak cur-
rent for duty cycles >40%. However, the LTC3853 uses
a patented scheme that counteracts this compensating
ramp, which allows the maximum inductor peak current
to remain unaffected throughout all duty cycles.
Inductor Value Calculation
Given the desired input and output voltages, the inductor
value and operating frequency, f OSC , directly determine
the inductor’s peak-to-peak ripple current:
I RIPPLE =
Lower ripple current reduces core losses in the inductor,
ESR losses in the output capacitors, and output voltage
ripple. Thus, highest efficiency operation is obtained at
low frequency with a small ripple current. Achieving this,
however, requires a large inductor.
A reasonable starting point is to choose a ripple current
that is about 40% of I OUT(MAX) . Note that the largest ripple
current occurs at the highest input voltage. To guarantee
that ripple current does not exceed a specified maximum,
the inductor should be chosen according to:
L ≥
f OSC ? I RIPPLE V IN
3853fa
相关PDF资料 |
PDF描述 |
|---|---|
| LT1619ES8#PBF | IC REG CTRLR PWM CM 8-SOIC |
| ABC13DRXI-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| ABC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| LTC3851EUD#PBF | IC REG CTRLR BUCK PWM CM 16-QFN |
| RCA24DTAD | CONN EDGECARD 48POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3853IUJ#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3853IUJ#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3854EDDB#PBF | 制造商:Linear Technology 功能描述:DP-SWREG/Controller, Cut Tape Small Footprint, Low Pin Count Synchronous Step-Do |
| LTC3854EDDB#TRMPBF | 功能描述:IC REG CTRLR BUCK PWM CM 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3854EDDB#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。