- 您现在的位置：买卖IC网 > PDF目录80200 > LTC3865IFE#PBF (LINEAR TECHNOLOGY CORP) DUAL SWITCHING CONTROLLER, 880 kHz SWITCHING FREQ-MAX, PDSO38 PDF资料下载
参数资料
| 型号： | LTC3865IFE#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | DUAL SWITCHING CONTROLLER, 880 kHz SWITCHING FREQ-MAX, PDSO38 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-38 |
| 文件页数： | 6/38页 |
| 文件大小： | 400K |
| 代理商： | LTC3865IFE#PBF |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
LTC3865/LTC3865-1
14
3865fb
bad mask is 100μs when there are any VID transitions.
On the LTC3865-1 (UH32 package) or the LTC3865 (FE38
package), each channel has its own PGOOD pin. Therefore,
the PGOOD pins now only respond to their own channels.
The PGOOD pins are allowed to be pulled up by external
resistors to sources of up to 6V.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>10%) as well as other more serious condi-
tions that may overvoltage the output. In such cases,
the top MOSFET is turned off and the bottom MOSFET is
turned on until the reverse current limit for the overvoltage
condition is reached. The bottom MOSFET will be turned on
again at the next clock and be turned off when the reverse
current limit is reached again. This process repeats until
the overvoltage condition is cleared.
OPERATION
Output Voltage Programming
The output voltages of both channels of the LTC3865/
LTC3865-1 can be programmed to a preset value. There
are two VID pins for each channel and by connecting these
pins to INTVCC, GND, or by oating them, the output volt-
ages can be set to the values in Table 1.
Table 1. Programming of Output Voltage
VID11/VID21
VID12/VID22
VOUT1/VOUT2 (V)
INTVCC
5.0
INTVCC
Float
3.3
INTVCC
GND
2.5
Float
INTVCC
1.8
Float
0.6 or External Divider
Float
GND
1.5
GND
INTVCC
1.2
GND
Float
1.0
GND
1.1
The Typical Application on the rst page is a basic LTC3865
application circuit. The LTC3865 can be congured to use
either DCR (inductor resistance) sensing or low value resis-
tor sensing. The choice between the two current sensing
schemes is largely a design trade-off between cost, power
consumption and accuracy. DCR sensing is becoming
popular because it saves expensive current sensing resis-
tors and is more power efcient, especially in high current
applications. However, current sensing resistors provide
the most accurate current limits for the controller. Other
external component selection is driven by the load require-
ment, and begins with the selection of RSENSE (if RSENSE is
used) and inductor value. Next, the power MOSFETs are se-
lected. Finally, input and output capacitors are selected.
Current Limit Programming
The ILIM pin is a tri-level logic input which sets the maxi-
mum current limit of the controller. When ILIM is either
grounded, oated or tied to INTVCC, the typical value for
the maximum current sense threshold will be 30mV, 50mV
or 75mV, respectively.
APPLICATIONS INFORMATION
Which setting should be used? For the best current limit
accuracy, use the 75mV setting. The 30mV setting will
allow for the use of very low DCR inductors or sense
resistors, but at the expense of current limit accuracy.
The 50mV setting is a good balance between the two. For
single output dual phase applications, use the 50mV or
75mV setting for optimal current sharing.
SENSE+ and SENSE– Pins
The SENSE+ and SENSE– pins are the inputs to the current
comparators. The common mode input voltage range of
the current comparators is 0V to 5V. Both SENSE pins
are high impedance inputs with small base currents of
less than 1μA. When the SENSE pins ramp up from 0V to
1.4V, the small base currents ow out of the SENSE pins.
When the SENSE pins ramp down from 5V to 1.1V, the
small base currents ow into the SENSE pins. The high
impedance inputs to the current comparators allow ac-
curate DCR sensing. However, care must be taken not to
oat these pins during normal operation.
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-T/10-D12N-C | 1-OUTPUT 51 W DC-DC REG PWR SUPPLY MODULE |
| LM9140AYM-10.0 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 10 V, PDSO8 |
| LM285BYZ-2.5X | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PBCY3 |
| LS4001-9PD1T | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LTC1436AACGN-PLL | SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3865IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3865IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3865IUH-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3865IUH-1#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3866EFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。