- 您现在的位置：买卖IC网 > PDF目录79926 > LTC3872ETS8#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | LTC3872ETS8#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 650 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | 1 MM HEIGHT, LEAD FREE, PLASTIC, MO-193, TSOT-23, 8 PIN |
| 文件页数： | 3/22页 |
| 文件大小： | 245K |
| 代理商： | LTC3872ETS8#PBF |
LTC3872
11
3872fb
Calculating Power MOSFET Switching and Conduction
Losses and Junction Temperatures
In order to calculate the junction temperature of the power
MOSFET,thepowerdissipatedbythedevicemustbeknown.
This power dissipation is a function of the duty cycle, the
load current and the junction temperature itself (due to
the positive temperature coefficient of its RDS(ON)). As a
result, some iterative calculation is normally required to
determineareasonablyaccuratevalue.Sincethecontroller
is using the MOSFET as both a switching and a sensing
element, care should be taken to ensure that the converter
is capable of delivering the required load current over all
operating conditions (line voltage and temperature), and
for the worst-case specifications for VSENSE(MAX) and the
RDS(ON) of the MOSFET listed in the manufacturer’s data
sheet.
ThepowerdissipatedbytheMOSFETinaboostconverteris:
PFET =
IO(MAX)
1– DMAX
2
RDS(ON) DMAX ρT
+k VO1.85
IO(MAX)
1– DMAX
(
)
CRSS f
The first term in the equation above represents the I2R
losses in the device, and the second term, the switching
losses.Theconstant,k=1.7,isanempiricalfactorinversely
related to the gate drive current and has the dimension
of 1/current.
From a known power dissipated in the power MOSFET, its
junction temperature can be obtained using the following
formula:
TJ = TA + PFET RTH(JA)
The RTH(JA) to be used in this equation normally includes
the RTH(JC) for the device plus the thermal resistance from
the case to the ambient temperature (RTH(CA)). This value
of TJ can then be compared to the original, assumed value
used in the iterative calculation process.
Output Diode Selection
To maximize efficiency, a fast switching diode with low
forwarddropandlowreverseleakageisdesired.Theoutput
diode in a boost converter conducts current during the
switch off-time. The peak reverse voltage that the diode
must withstand is equal to the regulator output voltage.
The average forward current in normal operation is equal
to the output current, and the peak current is equal to the
peak inductor current.
ID(PEAK) =IL(PEAK) = 1+
χ
2
IO(MAX)
1– DMAX
The power dissipated by the diode is:
PD = IO(MAX) VD
and the diode junction temperature is:
TJ = TA + PD RTH(JA)
The RTH(JA) to be used in this equation normally includes
the RTH(JC) for the device plus the thermal resistance from
the board to the ambient temperature in the enclosure.
Remember to keep the diode lead lengths short and to
observe proper switch-node layout (see Board Layout
Checklist) to avoid excessive ringing and increased dis-
sipation.
Output Capacitor Selection
Contributions of ESR (equivalent series resistance), ESL
(equivalent series inductance) and the bulk capacitance
mustbeconsideredwhenchoosingthecorrectcomponent
for a given output ripple voltage. The effects of these three
parameters (ESR, ESL and bulk C) on the output voltage
ripple waveform are illustrated in Figure 6e for a typical
boost converter.
The choice of component(s) begins with the maximum
acceptable ripple voltage (expressed as a percentage of
the output voltage), and how this ripple should be divided
between the ESR step and the charging/discharging
DV.
For the purpose of simplicity we will choose 2% for the
maximum output ripple, to be divided equally between the
ESRstepandthecharging/discharging
DV.Thispercentage
ripple will change, depending on the requirements of the
application, and the equations provided below can easily
be modified.
applicaTions inForMaTion
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3850EGN | 0.1 A DUAL SWITCHING CONTROLLER, 860 kHz SWITCHING FREQ-MAX, PDSO28 |
| LT1933HS6#TR | 1.05 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO6 |
| LC016AJ | 2-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE |
| LTC4224CMS-2#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4224IMS-1#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3872HDDB#TRMPBF | 功能描述:IC REG CTRLR BST PWM CM 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3872HDDB#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3872HTS8#PBF | 制造商:Linear Technology 功能描述:DP-SWREG/Controller, CUT TAPE No Rsense, Current Mode Boost DC/DC Controller |
| LTC3872HTS8#TRMPBF | 功能描述:IC REG CTRLR BST PWM CM TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3872HTS8#TRPBF | 功能描述:IC REG CTRLR BST PWM CM TSOT23-8 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。