- 您现在的位置：买卖IC网 > PDF目录16301 > LTC4010CFE#PBF (Linear Technology)IC CHARGER NIMH/NICD 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC4010CFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER NIMH/NICD 16-TSSOP |
| 标准包装： | 95 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
LTC4010
APPLICATIONS INFORMATION
V TEMP
TIMER
CHEM
+
10k
66.5k
–
V TEMP
V CELL
CHEM
+
10k
When the precharge state timer expires, the LTC4010
begins fast charge if V CELL is greater than 900mV. The
PWM, charge timer and internal termination control are
suspended if pause is asserted (V TEMP < 200mV), but all
status outputs continue to indicate charging is in progress.
The fast charge state continues until the selected voltage
or temperature termination criteria are met. Figure 9 sug-
gests termination based on ?T/?t, which for NiMH would
be an increase greater than 1°C per minute.
Because NiMH charging terminated due to ?T/?t and the
fast charge cycle had lasted more than t MAX /12 minutes,
the LTC4010 begins a top-off charge with a current of
I PROG /10. Top-off is an internally timed charge of t MAX /3
minutes with the CHRG output continuously asserted.
Finally, the LTC4010 enters the automatic recharge state
where the CHRG output is deasserted. The PWM is disabled
but V CDIV remains asserted to monitor V CELL . The charge
timer will be reset and fast charging will resume if V CELL
drops below 1.325V. The LTC4010 enters shutdown when
the DC adapter is removed, minimizing current draw from
the battery in the absence of an input power source.
While not a part of the sample waveforms of Figure 9,
temperature qualification is an ongoing part of the charg-
ing process, if an external thermistor network is detected
by the LTC4010. Should prescribed temperature limits be
exceeded during any particular charging state, charging
would be suspended until the sensed temperature returned
to an acceptable range.
A second possibility is to configure an LTC4010-based
charger to accept battery packs with varying numbers of
cells. By including R2 of the average cell voltage divider
network shown in Figure 3, battery-based programming
of the number of series-stacked cells could be realized
without defeating LTC4010 detection of battery insertion
or removal. Figure 11 shows a 2-cell NiMH battery pack
that programs the correct number of series cells when it is
connected to the charger, along with indicating chemistry
and providing temperature information.
Any of these battery pack charge control concepts could be
combined in a variety of ways to service custom application
needs. Charging parallel cells is not recommended.
BATTERY
PACK
8 3 5
NC
1200mAhr
NTC NiCd CELLS
4010 F10
Figure 10. NiCd Battery Pack with Time Limit Control
BATTERY
PACK
3 5 6
R2
1500mAhr
NTC NiMH CELLS
Battery-Controlled Charging
–
4010 F11
Because of the programming arrangement of the LTC4010,
it may be possible to configure it for battery-controlled
charging. In this case, the battery pack is designed to
provide customized information to an LTC4010-based
charger, allowing a single design to service a wide range
of application batteries. Assume the charger is designed
to provide a maximum charge current of 800mA (R SENSE =
125mΩ). Figure 10 shows a 4-cell NiCd battery pack for
which 800mA represents a 0.75C rate. When connected
to the charger, this pack would provide battery tempera-
ture information and correctly configure both fast charge
termination parameters and time limits for the internal
NiCd cells.
Figure 11. NiMH Battery Pack Indicating Number of Cells
PCB Layout Considerations
To prevent magnetic and electrical field radiation and
high frequency resonant problems, proper layout of the
components connected to the LTC4010 is essential. Refer
to Figure 12. For maximum efficiency, the switch node
rise and fall times should be minimized. The following
PCB design priority list will help ensure proper topology.
Layout the PCB using this specific order.
4010fb
0
相关PDF资料 |
PDF描述 |
|---|---|
| EMC12DRTH | CONN EDGECARD 24POS .100 EXTEND |
| RBA18DRMN | CONN EDGECARD 36POS .125 SQ WW |
| ECC20DRAS | CONN EDGECARD 40POS R/A .100 SLD |
| ABC08DRXN | CONN EDGECARD 16POS .100 DIP SLD |
| ABC08DRXH | CONN EDGECARD 16POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4010CFETR | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4010CFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4010EFE | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
发布紧急采购，3分钟左右您将得到回复。