- 您现在的位置：买卖IC网 > PDF目录80295 > LTC4012IUF-2#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 PDF资料下载
参数资料
| 型号： | LTC4012IUF-2#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封装： | 4 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-220WGGD-1, QFN-20 |
| 文件页数： | 4/28页 |
| 文件大小： | 381K |
| 代理商： | LTC4012IUF-2#PBF |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC4012/
LTC4012-1/LTC4012-2
4012fa
operation
Overview
The LTC4012 is a synchronous step-down (buck) current
mode PWM battery charger controller. The maximum
charge current is programmed by the combination of a
charge current sense resistor (RSENSE), matched input
resistors (RIN, Figure 1), and a programming resis-
tor (RPROG) between the PROG and GND pins. Battery
voltage is programmed with an external resistor divider
between FBDIV and GND (LTC4012) or two digital battery
voltage select pins (LTC4012-1/LTC4012-2). In addition,
the PROG pin provides a linearized voltage output of the
actual charge current.
The LTC4012 family does not have built-in charge termina-
tion and is flexible enough for charging any type of battery
chemistry. These are building block ICs intended for use
with an external circuit, such as a microcontroller, capable
of managing the entire algorithm required for the specific
battery being charged. Each member of the LTC4012 fam-
ily features a shutdown input and various state indicator
outputs, allowing easy and direct management by a wide
range of external (digital) charge controllers. Due to the
popularity of rechargeable Lithium-Ion chemistries, the
LTC4012-1 and LTC4012-2 also offer internal precision
resistors that can be digitally selected to produce one of
four preset output voltages for simplified design of those
charger types.
Shutdown
The LTC4012 remains in shutdown until DCIN is greater
than 5.1V and exceeds CLP by 60mVand SHDN is driven
above 1.4V. In shutdown, current drain from the battery
is reduced to the lowest possible level, thereby increasing
standby time. When in shutdown, the ITH pin is pulled to
GND and CHRG, ICL, FET gate drivers and INTVDD output
are all disabled. The charging can be stopped at any time
by forcing SHDN below 300mV.
AC Present Indication
The ACP status output correctly indicates sensed adapter
input voltage during all LTC4012 states. AC present is
indicated (ACP output low) as soon as DCIN exceeds
BAT by at least 500mV. Charging is not enabled until this
conditionisfirstmet.Afterthisevent,chargingisnolonger
gated by AC present detection. If battery voltage rises due
to ESR, or DCIN droops due to current load, AC present
may no longer be indicated by the IC if charging was
started with very low input overhead. However, charging
will remain enabled unless DCIN falls below the supply
voltage on CLP.
Input PowerPath Control
The input PFET controller performs many important func-
tions. First, it monitors DCIN and enables the charger
when this input voltage is higher than the raw CLP sys-
tem supply. Next, it controls the gate of an external input
power PFET to maintain a low forward voltage drop when
charging, creating improved efficiency. It also prevents
reverse current flow through this same PFET, providing
a suitable input blocking function. Finally, it helps avoid
synchronous boost operation during invalid operating
conditions by detecting elevated CLP voltage and forcing
the charger off.
If DCIN voltage is less than CLP, then DCIN must rise
60mV higher than CLP to enable the charger and activate
the ideal diode control. At this point, the ACPb status
output also transitions to low impedance to indicate
to the host system that an external adapter is present.
The gate of the input PFET is driven to a voltage sufficient
to regulate a forward drop between DCIN and CLP of about
25mV. If the input voltage differential drops below this
point, the FET is turned off slowly. If the voltage between
DCIN and CLP drops to less than –25mV, the input FET is
turned off in less than 6s to prevent significant reverse
current from flowing back through the PFET. In this case,
ACPb also switches back to high impedance and the
charger is disabled.
Soft-Start
Exitingtheshutdownstateenablesthechargerandreleases
the ITH pin. When enabled, switching will not begin until
DCIN exceeds BAT by 500mV and ITH exceeds a threshold
that assures initial current will be positive (about 5% to
25%ofthemaximumprogrammedcurrent).Tolimitinrush
current, soft-start delay is created with the compensation
values used on the ITH pin. Longer soft-start times can be
realized by increasing the filter capacitor on ITH, if reduced
loop bandwidth is acceptable. The actual charge current at
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4012IUF-2#TRPBF | SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3611EWP#TR | 10 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC64 |
| LT3509EMSE#PBF | 1.2 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO16 |
| LQN-1.5/50-D12MB-C | DC-DC REG PWR SUPPLY MODULE |
| LKP5740-7ERD6TB1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4012IUF-3#PBF | 功能描述:IC BATT CHRGR MC HI-EFF 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4012IUF-3#TRPBF | 功能描述:IC CTLR BATT CHARGER CC/CV 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4012IUF-3-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency, Multi-Chemistry Battery Charger with PowerPath Control |
| LTC4012IUF-3-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency, Multi-Chemistry Battery Charger with PowerPath Control |
| LTC4020EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Charger Lead-Acid/Li-FePO4/Li-Ion/Li-Pol 20000mA 55V 38-Pin QFN EP 制造商:Linear Technology 功能描述:IC BATT CHARGER 55V BB 38QFN 制造商:Linear Technology 功能描述:BATTERY CHARGER, 20A, QFN-38 制造商:Linear Technology 功能描述:BATTERY CHARGER, 20A, QFN-38, Input Voltage:55V, Battery Charge Voltage:55V, Charge Current Max:20A, Battery IC Case Style:QFN, No. of Pins:38, No. of Series Cells:12, Operating Temperature Min:-40C, Operating Temperature Max:125C , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。