- 您现在的位置：买卖IC网 > PDF目录80295 > LTC4012IUF-2#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 PDF资料下载
参数资料
| 型号： | LTC4012IUF-2#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封装： | 4 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, MO-220WGGD-1, QFN-20 |
| 文件页数： | 7/28页 |
| 文件大小： | 381K |
| 代理商： | LTC4012IUF-2#PBF |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
4012fa
LTC4012/
LTC4012-1/LTC4012-2
The ITH output of the error amplifier is a scaled control
voltage for one input of the PWM comparator CC. ITH
sets a peak inductor current threshold, sensed by R1, to
maintain the desired average current through RSENSE. The
currentcomparatoroutputdoesthisbyswitchingthestate
of the RS latch at the appropriate time.
At the beginning of each oscillator cycle, the PWM
clock sets the RS latch and turns on the external top-
side NFET (bottom-side synchronous NFET off) to
refresh the current carried by the external inductor L1.
The inductor current and voltage across RSENSE begin
to rise linearly. CA buffers this instantaneous voltage
rise and applies it to CC with gain supplied by R1.
When the voltage across R1 exceeds the peak level set by
the ITH output of EA, the top FET turns off and the bottom
FET turns on. The inductor current then ramps down lin-
early until the next rising PWM clock edge. This closes the
loop and sources the correct inductor current to maintain
the desired parameter (charge current, battery voltage,
or input current). To produce a near constant frequency,
the PWM oscillator implements the equation:
t
CLP BAT
CLP
kHz
OFF =
–
550
Repetitive, closed-loop waveforms for stable PWM opera-
tion appear in Figure 2.
PWM Watchdog Timer
Asinputandoutputconditionsvary,theLTC4012mayneed
toutilizePWMdutycyclesapproaching100%.Inthiscase,
operating frequency may be reduced well below 550kHz.
An internal watchdog timer observes the activity on the
TGATEpin.IfTGATEisonformorethan40s,thewatchdog
activates and forces the bottom NFET on (top NFET off)
for about 100ns. This avoids a potential source of audible
noise when using ceramic input or output capacitors and
prevents the boost supply capacitor for the top gate driver
from discharging. In low drop out operation, the actual
charge current may not be able to reach the programmed
full-scale value due to the watchdog function.
Overvoltage Protection
The LTC4012 also contains overvoltage detection that
preventstransientbatteryvoltageovershootsofmorethan
about 6% above the programmed output voltage. When
batteryovervoltageisdetected,bothexternalMOSFETsare
turned off until the overvoltage condition clears, at which
time a new soft start sequence begins. This is useful for
properlychargingbatterypacksthatuseaninternalswitch
to disconnect themselves for performing functions such
as calibration or pulse mode charging.
Reverse Charge Current Protection (Anti-Boost)
Because the LTC4012 always attempts to operate syn-
chronously in full continuous mode (to avoid audible
noise from ceramic capacitors), reverse average charge
current can occur during some invalid operating condi-
tions. INFET PowerPath control avoids boosting a lightly
loaded system supply during reverse operation. However,
under heavier system loads, CLP may not boost above
DCIN, even though reverse average current is flowing. In
this case a second circuit monitors indication of reverse
average current on PROG.
If either of these circuits detects boost operation, The
LTC4012 turns off both external MOSFETs until the reverse
current condition clears. At that point, a new soft-start
sequence begins.
operation
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4012IUF-2#TRPBF | SWITCHING CONTROLLER, 633 kHz SWITCHING FREQ-MAX, PQCC20 |
| LTC3611EWP#TR | 10 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC64 |
| LT3509EMSE#PBF | 1.2 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, PDSO16 |
| LQN-1.5/50-D12MB-C | DC-DC REG PWR SUPPLY MODULE |
| LKP5740-7ERD6TB1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4012IUF-3#PBF | 功能描述:IC BATT CHRGR MC HI-EFF 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4012IUF-3#TRPBF | 功能描述:IC CTLR BATT CHARGER CC/CV 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4012IUF-3-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency, Multi-Chemistry Battery Charger with PowerPath Control |
| LTC4012IUF-3-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency, Multi-Chemistry Battery Charger with PowerPath Control |
| LTC4020EUHF#PBF | 制造商:Linear Technology 功能描述:Battery Charger Lead-Acid/Li-FePO4/Li-Ion/Li-Pol 20000mA 55V 38-Pin QFN EP 制造商:Linear Technology 功能描述:IC BATT CHARGER 55V BB 38QFN 制造商:Linear Technology 功能描述:BATTERY CHARGER, 20A, QFN-38 制造商:Linear Technology 功能描述:BATTERY CHARGER, 20A, QFN-38, Input Voltage:55V, Battery Charge Voltage:55V, Charge Current Max:20A, Battery IC Case Style:QFN, No. of Pins:38, No. of Series Cells:12, Operating Temperature Min:-40C, Operating Temperature Max:125C , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。