- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4058XEDD-4.2#TRPBF (Linear Technology)IC BATT CHARGER LI-ION REG 8DFN PDF资料下载
参数资料
| 型号： | LTC4058XEDD-4.2#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION REG 8DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LTC4058-4.2/LTC4058X-4.2
APPLICATIO S I FOR ATIO
120 ° C – T A
( V CC – V BAT ) ? θ JA
=
=
( ) ? 50 ° C / W 85 ° C / A
The LTC4058 can be used above 52°C ambient but the
charge current will be reduced from 800mA. The approxi-
mate current at a given ambient temperature can be
approximated by:
I BAT =
Using the previous example with an ambient temperature
of 60 ° C, the charge current will be reduced to
approximately:
120 ° C – 60 ° C 60 ° C
I BAT
5 V – 3 . 3 V
I BAT = 706 mA
Moreover, when thermal feedback reduces the charge cur-
rent the voltage at the PROG pin is also reduced proportion-
ally as discussed in the Operation section. It is important
to remember that LTC4058 applications do not need to be
designed for worst-case thermal conditions since the IC will
automatically reduce power dissipation when the junction
temperature reaches approximately 120 ° C.
Thermal Considerations
In order to deliver maximum charge current under all
conditions, it is critical that the exposed metal pad on the
backside of the LTC4058 package is soldered to the PC
board ground. Correctly soldered to a 2500mm 2 double-
sided 1oz copper board, the LTC4058 has a thermal
resistance of approximately 40 ° C/W. Failure to make
thermal contact between the exposed pad on the back-
ceramic capacitors. Because of the self-resonant and high
Q characteristics of some types of ceramic capacitors,
high voltage transients can be generated under some
start-up conditions such as connecting the charger input
to a live power source. Adding a 1.5 ? resistor in series
with an X5R ceramic capacitor will minimize start-up
voltage transients. For more information, see Application
Note 88.
Charge Current Soft-Start
The LTC4058 includes a soft-start circuit to minimize the
inrush current at the start of a charge cycle. When a charge
cycle is initiated, the charge current ramps from zero to
the full-scale current over a period of approximately 100 μ s.
This has the effect of minimizing the transient current load
on the power supply during start-up.
USB and Wall Adapter Power
The LTC4058 allows charging from both a wall adapter
and a USB port. Figure 3 shows an example of how to
combine wall adapter and USB power inputs. A P-channel
MOSFET, MP1, is used to prevent back conducting into
the USB port when a wall adapter is present and a
Schottky diode, D1, is used to prevent USB power loss
through the 1k pull-down resistor.
Typically a wall adapter can supply more current than the
500mA-limited USB port. Therefore, an N-channel
MOSFET, MN1, and an extra 3.3k program resistor are
used to increase the charge current to 800mA when the
wall adapter is present.
side of the package and the copper board will result in
thermal resistances far greater than 40 ° C/W. As an
example, a correctly soldered LTC4058 can deliver over
800mA to a battery from a 5V supply at room tempera-
ture. Without a backside thermal connection, this num-
ber will drop considerably.
5V WALL
ADAPTER
800mA I CHG
USB POWER
500mA I CHG
MP1
D1
6
4, 9
LTC4058-4.2
BAT
V CC BSENSE
GND PROG
3.3k
2
1
5
I CHG
+
SYSTEM
LOAD
Li-Ion
BATTERY
V CC Bypass Capacitor
Many types of capacitors can be used for input bypassing,
1k
MN1
2k
405842 F03
however, caution must be exercised when using multilayer
Figure 3. Combining Wall Adapter and USB Power
sn405842 405842fs
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4059AEDC#TRMPBF | IC BATT CHARGER LI-ION REG 6DFN |
| LTC4060EDHC#TRPBF | IC BATT CHARGER NIMH/NICD 16DFN |
| LTC4061EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4062EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4059 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4059A | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4059AEDC#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 500mA 4.2V 6-Pin DFN EP |
| LTC4059AEDC#TR | 功能描述:IC BATT CHARGER LI-ION REG 6DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4059AEDC#TRM | 功能描述:IC BATT CHARGER LI-ION REG 6DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。