- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4058XEDD-4.2#TRPBF (Linear Technology)IC BATT CHARGER LI-ION REG 8DFN PDF资料下载
参数资料
| 型号： | LTC4058XEDD-4.2#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION REG 8DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LTC4058-4.2/LTC4058X-4.2
OPERATIO
R PROG =
, I CHG =
The LTC4058 is a single cell lithium-ion battery charger
using a constant-current/constant-voltage algorithm. It
can deliver up to 950mA of charge current (using a good
thermal PCB layout) with a final float voltage accuracy of
± 1%. The LTC4058 includes an internal P-channel power
MOSFET and thermal regulation circuitry. No blocking
diode or external current sense resistor is required; thus,
the basic charger circuit requires only two external com-
ponents. Furthermore, the LTC4058 is capable of operat-
ing from a USB power source.
Normal Charge Cycle
A charge cycle begins when the voltage at the V CC pin rises
above the UVLO threshold level and a 1% program resistor
is connected from the PROG pin to ground. If the BSENSE
pin is less than 2.9V, the charger enters trickle charge mode.
In this mode, the LTC4058 supplies approximately 1/10th
the programmed charge current to bring the battery volt-
age up to a safe level for full current charging. (Note: The
LTC4058X does not include this trickle charge feature.)
When the BSENSE pin voltage rises above 2.9V, the charger
enters constant-current mode where the programmed
charge current is supplied to the battery. When the BSENSE
pin approaches the final float voltage (4.2V), the LTC4058
enters constant-voltage mode and the charge current be-
gins to decrease. When the charge current drops to 1/10th
of the programmed value, the charge cycle ends.
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. The charge current out of
the BAT pin is 1000 times the current out of the PROG pin.
The program resistor and the charge current are calcu-
lated using the following equations:
1000 V 1000 V
I CHG R PROG
Charge current out of the BAT pin can be determined at any
time by monitoring the PROG pin voltage and using the
following equation:
Charge Termination
The charge cycle terminates when the charge current falls
to 10% the programmed value after the final float voltage
is reached. This condition is detected by using an internal,
filtered comparator to monitor the PROG pin. When the
PROG pin voltage falls below 100mV 1 for longer than
t TERM (typically 1ms), charging is terminated. The charge
current is latched off and the LTC4058 enters standby
mode where the input supply current drops to 200 μ A.
(Note: C/10 termination is disabled in trickle charging and
thermal limiting modes.)
When charging, transient loads on the BAT pin can cause
the PROG pin to fall below 100mV for short periods of time
before the DC charge current has dropped to 10% of the
programmed value. The 1ms filter time (t TERM ) on the
termination comparator ensures that transient loads of
this nature do not result in premature charge cycle termi-
nation. Once the average charge current drops below 10%
of the programmed value, the LTC4058 terminates the
charge cycle and ceases to provide any current through
the BAT pin. In this state, all loads on the BAT pin must be
supplied by the battery.
The LTC4058 constantly monitors the BAT pin voltage in
standby mode. If this voltage drops below the 4.1V recharge
threshold (V RECHRG ), another charge cycle begins and
charge current is once again supplied to the battery. To
manually restart a charge cycle when in standby mode, the
input voltage must be removed and reapplied or the charger
must be shut down and restarted using the EN pin. Figure 1
shows the state diagram of a typical charge cycle.
Charge Status Indicator (CHRG)
The charge status output has two states: pull-down and
high impedance. The pull-down state indicates that the
LTC4058 is in a charge cycle. Once the charge cycle has
terminated or the LTC4058 is disabled, the pin state
becomes high impedance.
1 Any external sources that hold the PROG pin above 100mV will prevent the LTC4058 from
terminating a charge cycle.
I BAT =
V PROG
R PROG
? 1000
sn405842 405842fs
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4059AEDC#TRMPBF | IC BATT CHARGER LI-ION REG 6DFN |
| LTC4060EDHC#TRPBF | IC BATT CHARGER NIMH/NICD 16DFN |
| LTC4061EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4062EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4059 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4059A | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4059AEDC#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 500mA 4.2V 6-Pin DFN EP |
| LTC4059AEDC#TR | 功能描述:IC BATT CHARGER LI-ION REG 6DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4059AEDC#TRM | 功能描述:IC BATT CHARGER LI-ION REG 6DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。