- 您现在的位置：买卖IC网 > PDF目录16040 > LTC4059EDC#TRMPBF (Linear Technology)IC BATT CHARGER LI-ION REG 6DFN PDF资料下载
参数资料
| 型号： | LTC4059EDC#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION REG 6DFN |
| 标准包装： | 500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 3.75 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN 裸露焊盘 |
| 供应商设备封装： | 6-DFN-EP（2x2） |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC4059EDC#PBF LTC4059EDC#PBF-ND |
LTC4059/LTC4059A
APPLICATIO S I FOR ATIO
Shutdown Mode
Charging can be terminated by pulling the EN pin above the
shutdown threshold (approximately 0.92V). In shutdown
mode, the battery drain current is reduced to less than 1 μ A
and the supply current to 10 μ A.
USB and Wall Adapter Power
Although the LTC4059/LTC4059A allow charging from a
USB port, a wall adapter can also be used to charge Li-Ion
batteries. Figure 3 shows an example of how to combine
wall adapter and USB power inputs. A P-channel MOSFET,
MP1, is used to prevent back conducting into the USB port
when a wall adapter is present and Schottky diode, D1, is
used to prevent USB power loss through the 1k pull-down
resistor.
Typically a wall adapter can supply significantly more
current than the 500mA limited USB port. Therefore, an
N-channel MOSFET, MN1, and an extra program resistor
are used to increase the charge current to 850mA when the
wall adapter is present.
ance of the current source pair, M1 and M2 (note that M1
is the internal P-channel power MOSFET). It ensures that
the drain current of M1 is exactly 1000 times greater than
the drain current of M2.
Amplifiers CA and VA are used in separate feedback loops
to force the charger into constant-current or voltage
mode, respectively. Diodes D1 and D2 provide priority to
either the constant-current or constant-voltage loop;
whichever is trying to reduce the charge current the most.
The output of the other amplifier saturates low which
effectively removes its loop from the system. When in
constant-current mode, CA servos the voltage at the
PROG pin to be 1.21V. VA servos its inverting input to
precisely 1.21V when in constant-voltage mode and the
internal resistor divider made up of R1 and R2 ensures
that the battery voltage is maintained at 4.2V. The PROG
pin voltage gives an indication of the charge current
during constant-voltage mode as discussed in the Pro-
gramming Charge Current section.
Transconductance amplifier, TA, limits the die tempera-
ture to approximately 115 ° C when in constant-tempera-
5V WALL
ADAPTER
850mA I CHG
USB
POWER
500mA I CHG
MP1
D1
4
BAT
LTC4059
V CC
PROG
3
5
I CHG
+
SYSTEM
LOAD
Li-Ion
BATTERY
ture mode. TA acts in conjunction with the constant-current
loop. When the die temperature exceeds approximately
115 ° C, TA sources current through R3. This causes CA to
reduce the charge current until the PROG pin voltage plus
the voltage across R3 equals 1.21V. Diode D3 ensures that
1k
MN1 3.4k
2.43k
4059 F03
TA does not affect the charge current when the die tem-
perature is below approximately 115 ° C. The PROG pin
voltage continues to give an indication of the charge
current.
Figure 3. Combining Wall Adapter and USB Power
Constant Current/Constant Voltage/
Constant Temperature
The LTC4059/LTC4059A use a unique architecture to
charge a battery in a constant-current, constant-voltage
and constant-temperature fashion. Figures 1 and 2 show
simplified block diagrams of the LTC4059 and LTC4059A
respectively. Three of the amplifier feedback loops shown
control the constant-current, CA, constant-voltage, VA,
and constant-temperature, TA modes. A fourth amplifier
feedback loop, MA, is used to increase the output imped-
In typical operation, the charge cycle begins in constant-
current mode with the current delivered to the battery
equal to 1210V/R PROG . If the power dissipation of the
LTC4059/LTC4059A results in the junction temperature
approaching 115 ° C, the amplifier (TA) will begin decreas-
ing the charge current to limit the die temperature to
approximately 115 ° C. As the battery voltage rises, the
LTC4059/LTC4059A either return to constant-current mode
or enter constant-voltage mode straight from constant-
temperature mode. Regardless of mode, the voltage at the
PROG pin is proportional to the current delivered to the
battery.
4059fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| IMC1210ER270K | INDUCTOR WW 27UH 10% 1210 |
| LTC4059EDC#TRPBF | IC BATT CHARGER LI-ION REG 6DFN |
| EMM10DRYN | CONN EDGECARD 20POS DIP .156 SLD |
| LTC4059EDC#TR | IC BATT CHARGER LI-ION REG 6DFN |
| IMC1210ER220K | INDUCTOR WW 22UH 10% 1210 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4060 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear NiMH/NiCd Fast Battery Charger |
| LTC4060EDHC | 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 2000mA -0.3V to 10.3V 16-Pin DFN EP |
| LTC4060EDHC#PBF | 功能描述:IC BATT CHARGER NIMH/NICD 16DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4060EDHC#TR | 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 2000mA -0.3V to 10.3V 16-Pin DFN EP T/R |
| LTC4060EDHC#TRPBF | 功能描述:IC BATT CHARGER NIMH/NICD 16DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。