- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4061EDD#TRPBF (Linear Technology)IC BATT CHARGER LI-ION 10-DFN PDF资料下载
参数资料
| 型号： | LTC4061EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 10-DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.3 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
LTC4061
APPLICATIONS INFORMATION
I DETECT =
? I CHG =
R PROG 100 V
R DET =
+
C TIMER
2k R DET GND
1k
When the programmed time has elapsed, the charge
cycle terminates and the charger enters standby mode.
Subsequent recharge cycles terminate when 50% of the
programmed time has elapsed. The I DET pin determines
the behavior of the CHRG output. Connecting a resistor
(R DET ) from the I DET pin to ground sets the charge current
detection threshold, I DETECT :
or
10 R DET R DET
100 V
I DE T ECT
When the charge current (I BAT ) is greater than
I DETECT , the CHRG output is in its pull-down state. When
the charger enters constant voltage mode operation and
the charge current falls below I DETECT , the CHRG output
becomes high impedance, indicating that the battery is
almost fully charged. The CHRG output will also become
high impedance once the charge time elapses. If the I DET
pin is not connected, the CHRG output remains in its pull-
down state until the charge time elapses and terminates
the charge cycle.
Figure 2 shows a charger circuit using charge time termi-
nation that is programmed to charge at 500mA. Once the
charge current drops below 100mA in constant voltage
mode (as set by R DET ), the CHRG output turns off the
LED. This indicates to the user that the battery is almost
fully charged and ready to use. The LTC4061 continues
to charge the battery until the internal timer reaches 3
hours (as set by C TIMER ). During recharge cycles, the
LTC4061 charges the battery until the internal timer reaches
500mA
V IN V CC BAT
C/5 LTC4061
CHRG
PROG TIMER
R PROG I DET
0.1μF
4061 F02
Figure 2. Time Termination Mode.
The Charge Cycle Ends After 3 Hours.
1.5 hours. Figure 3 describes the operation of the LTC4061
charger when charge time termination is used.
Charge Current Termination
Connecting the TIMER pin to ground selects charge cur-
rent termination. With this method, the timer is disabled
and a resistor (R DET ) must be connected from the I DET
pin to ground. I DETECT is programmed using the same
equation stated in the previous section. The charge cycle
terminates when the charge current falls below I DETECT .
This condition is detected using an internal filtered
comparator to monitor the I DET pin. When the I DET pin
falls below 100mV for longer than t TERM (typically 1ms),
charging is terminated.
When charging, transient loads on the BAT pin can cause
the I DET pin to fall below 100mV for short periods of time
before the DC current has dropped below the I DETECT
threshold. The 1.5ms filter time (t TERM ) on the internal
comparator ensures that transient loads of this nature do
not result in premature charge cycle termination. Once the
average charge current drops below I DETECT , the charger
terminates the charge cycle.
The CHRG output is in a pull-down state while charging
and in a high impedance state once charging has stopped.
Figure 4 describes the operation of the LTC4061 charger
when charge current termination is used.
User-Selectable Charge Termination
Connecting the TIMER pin to V CC selects user-selectable
charge termination, in which all of the internal termination
features are disabled. The charge cycle continues indefi-
nitely until the charger is shut down through the EN pin.
The I DET pin programs the behavior of the CHRG output in
the same manner as when using charge time termination.
If the I DET pin is not connected, the CHRG output remains
in its pull-down state until the charger is shut down.
With user-selectable charge termination, the SmartStart
feature is disabled; when the charger is powered on or
enabled, the LTC4061 automatically begins charging,
regardless of the battery voltage. Figure 5 describes
charger operation when user-selectable charge termina-
tion is used.
4061fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4062EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
| LTC4064EMSE#TRPBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4065EDC#TRPBF | IC CHARGER BATT LI-ON 6-DFN |
| LTC4066EPF#TRPBF | IC USB POWER MANAGER 24-UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4062 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4062EDD | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 800mA 4.2V 10-Pin DFN EP |
| LTC4062EDD#PBF | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4062EDD#TRPBF | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4063 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-lon Battery Charger with Thermistor Input |
发布紧急采购，3分钟左右您将得到回复。