- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4061EDD#TRPBF (Linear Technology)IC BATT CHARGER LI-ION 10-DFN PDF资料下载
参数资料
| 型号： | LTC4061EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER LI-ION 10-DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.3 V ~ 8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
LTC4061
PIN FUNCTIONS
C TIMER
TIME ( HOURS ) = 3 HOURS ? or
C TIMER = 0 . 1 μF ?
I DETECT =
? I CHG =
R PROG 100 V
R DET =
BAT (Pin 1): Charge Current Output. This pin provides
charge current to the battery and regulates the final float
voltage to 4.2V.
NTC (Pin 2): Input to the NTC (Negative Temperature Coef-
ficient) Thermistor Temperature Monitoring Circuit. Under
normal operation, connect a thermistor from the NTC pin
to ground and a resistor of equal value from the NTC pin
to V CC . When the voltage at this pin drops below 0.35 ?
V CC at hot temperatures or rises above 0.76 ? V CC at cold,
charging is suspended, the internal timer is frozen and the
CHRG pin output will start to pulse at 1.5Hz. Pulling this
pin below 0.016 ? V CC disables the NTC feature. There is
approximately 2°C of temperature hysteresis associated
with each of the input comparators thresholds.
TIMER (Pin 3): Timer Program and Termination Select Pin.
This pin selects which method is used to terminate the
charge cycle. Connecting a capacitor, C TIMER , to ground
selects charge time termination. The charge time is set
by the following formula:
0 . 1 μF
TIME (HOURS)
3 ( HOURS )
Connecting the TIMER pin to ground selects charge cur-
rent termination, while connecting the pin to V CC selects
user termination. See Applications Information for more
information on current and user termination.
ACPR (Pin 4): Open-Drain Power Supply Present Status
Output. The power supply status indicator pin has two
states: pull-down and high impedance. This output can
be used as a logic interface or as a LED driver. In the
pull-down state, an NMOS transistor capable of sinking
10mA pulls down on the ACPR pin. The state of this pin
is dependent on the value of V CC and BAT: it requires that
V CC is 190mV greater than V BAT and greater than V UVLO .
See Applications Information.
CHRG (Pin 5): Open-Drain Charge Status Output. The
charge status indicator pin has three states: pull-down,
pulse at 1.5Hz or 6Hz and high impedance. This output
can be used as a logic interface or as a LED driver. In the
pull-down state, an NMOS transistor capable of sinking
10mA pulls down on the CHRG pin. The state of this pin
depends on the value of I DETECT as well as the termina-
tion method being used and the state of the NTC pin. See
Applications Information.
C/5 (Pin 6): C/5 Enable Input. Used to control the amount
of current drawn from the USB port. A logic high on the
C/5 pin sets the current limit to 100% of the current
programmed by the PROG pin. A logic low on the C/5 pin
sets the current limit to 20% of the current programmed
by the PROG pin. An internal 3M Ω pull-down resistor
defaults the C/5 pin to its low current state.
EN (Pin 7): Charger Enable Input. A logic high on the EN pin
places the charger into shutdown mode, where the input
quiescent current is less than 50μA. A logic low on this
pin enables charging. An internal 3M Ω pull-down resistor
to ground defaults the charger to its enabled state.
I DET (Pin 8) : Current Detection Threshold Program Pin.
The current detection threshold, I DETECT , is set by con-
necting a resistor, R DETECT , to ground. I DETECT is set by
the following formula:
or
10 R DET R DET
100 V
I DE T ECT
The CHRG pin becomes high impedance when the charge
current drops below I DETECT . I DETECT can be set to 1/10th
the programmed charge current by connecting I DET di-
rectly to PROG. If the I DET pin is not connected, the CHRG
output remains in its pull-down state until the charge time
elapses and terminates the charge cycle. See Applications
Information.
This pin is clamped to approximately 2.4V. Driving this pin to
voltages beyond the clamp voltage should be avoided.
PROG (Pin 9): Charge Current Program and Charge Cur-
rent Monitor. The charge current is set by connecting a
4061fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4062EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
| LTC4064EMSE#TRPBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4065EDC#TRPBF | IC CHARGER BATT LI-ON 6-DFN |
| LTC4066EPF#TRPBF | IC USB POWER MANAGER 24-UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4062 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:Standalone 250mA Li-Ion Battery Charger in 2 × 2 DFN |
| LTC4062EDD | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 800mA 4.2V 10-Pin DFN EP |
| LTC4062EDD#PBF | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4062EDD#TRPBF | 功能描述:IC BATT CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4063 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-lon Battery Charger with Thermistor Input |
发布紧急采购，3分钟左右您将得到回复。