- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4066EPF#TRPBF (Linear Technology)IC USB POWER MANAGER 24-UTQFN PDF资料下载
参数资料
| 型号： | LTC4066EPF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/28页 |
| 文件大小： | 0K |
| 描述： | IC USB POWER MANAGER 24-UTQFN |
| 标准包装： | 2,500 |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-UFQFN 裸露焊盘 |
| 供应商设备封装： | 24-UTQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC4066/LTC4066-1
APPLICATIONS INFORMATION
Battery Charger
The battery charger circuits of the LTC4066/LTC4066-1
are designed for charging single cell lithium-ion batter-
ies. Featuring an internal P-channel power MOSFET, the
charger uses a constant-current/constant-voltage charge
algorithm with programmable current and a program-
mable timer for charge termination. Charge current can be
programmed up to 1.5A. The ?nal ?oat voltage accuracy
is ±0.8% typical. No blocking diode or sense resistor is
required when powering the IN pin. The CHRG open-drain
status output provides information regarding the charging
status of the LTC4066/LTC4066-1 at all times. An NTC
input provides the option of charge quali?cation using
battery temperature.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
preset value of approximately 105°C. This feature protects
the LTC4066/LTC4066-1 from excessive temperature, and
allows the user to push the limits of the power handling
capability of a given circuit board without risk of dam-
aging the LTC4066/LTC4066-1. Another bene?t of the
LTC4066/LTC4066-1 thermal limit is that charge current
can be set according to typical, not worst-case, ambient
temperatures for a given application with the assurance
that the charger will automatically reduce the current in
worst-case conditions.
The charge cycle begins when the voltage at the OUT pin
rises above the output UVLO level and the battery voltage
is below the recharge threshold. No charge current actually
?ows until the OUT voltage is greater than the output UVLO
level and 100mV above the BAT voltage. At the beginning
of the charge cycle, if the battery voltage is below 2.8V,
the charger goes into trickle charge mode to bring the
cell voltage up to a safe level for charging. The charger
goes into the fast charge constant-current mode once
the voltage on the BAT pin rises above 2.8V. In constant-
current mode, the charge current is set by R PROG . When
the battery approaches the ?nal ?oat voltage, the charge
current begins to decrease as the LTC4066/LTC4066-1
switches to constant-voltage mode. When the charge
current drops below a level programmed by the I STAT pin
while in constant-voltage mode the CHRG pin assumes a
high impedance state.
An external capacitor on the TIMER pin sets the total
minimum charge time. When this time elapses the
charge cycle terminates and the CHRG pin assumes a
high impedance state, if it has not already done so. While
charging in constant-current mode, if the charge current
is decreased by thermal regulation or in order to maintain
the programmed input current limit the charge time is
automatically increased. In other words, the charge time
is extended inversely proportional to charge current de-
livered to the battery. For Li-Ion and similar batteries that
require accurate ?nal ?oat potential, the internal bandgap
reference, voltage ampli?er and the resistor divider provide
regulation with ±0.8% accuracy.
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage
is low (below 2.8V) the charger goes into trickle charge
reducing the charge current to 10% of the full-scale current.
If the low-battery voltage persists for one quarter of the
total charge time, the battery is assumed to be defective,
the charge cycle is terminated and the CHRG pin output
assumes a high impedance state. If for any reason the
battery voltage rises above ~2.8V, the charge cycle will
be restarted. To restart the charge cycle (i.e., when the
dead battery is replaced with a discharged battery), simply
remove the input voltage and reapply it, cycle the TIMER
pin to 0V or cycle the SHDN pin to 0V.
4066fc
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4067EDE#TRPBF | IC USB POWER MANAGER 12-DFN |
| LTC4068EDD-4.2#PBF | IC CHARGER BATT LI-ON 8-DFN |
| LTC4069EDC#TRPBF | IC CHARGER LI-ION 6-DFN |
| LTC4070IMS8E#TRPBF | IC BATT CHRGR LIION/POLY 8MSOP |
| LTC4071IMS8E#TRPBF | IC LI-ION/POLY BATT CHRGR 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4066EUF#PBF | 功能描述:IC USB POWER MANAGER 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4066EUF#TRPBF | 功能描述:IC USB POWER MANAGER 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4066EUF-1#PBF | 功能描述:IC USB POWER MANAGER 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4066EUF-1#TRPBF | 功能描述:IC USB POWER MANAGER 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4067 | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB Power Manager with OVP and Li-Ion/Polymer Charger |
发布紧急采购，3分钟左右您将得到回复。