- 您现在的位置：买卖IC网 > PDF目录16310 > LTC4067EDE#PBF (Linear Technology)IC USB POWER MANAGER 12-DFN PDF资料下载
参数资料
| 型号： | LTC4067EDE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/20页 |
| 文件大小： | 0K |
| 描述： | IC USB POWER MANAGER 12-DFN |
| 标准包装： | 91 |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 5.5V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-DFN（4x3） |
| 包装： | 管件 |
LTC4067
TYPICAL APPLICATIO S
Li-Ion Charger from 5V Wall Adapter with Overvoltage
Protection
Figure 5 illustrates an application where the LTC4067 is
used to charge a single-cell Li-Ion battery from a wall
adapter with built-in overvoltage protection.
Overvoltage protection is achieved with the OVI and OVP
pins of the LTC4067 along with an external PFET in se-
ries with the IN pin. This PFET disconnects the LTC4067
from potentially damaging overvoltage conditions that
are caused by attaching the wrong wall adapter. When
the OVI input senses a voltage greater than V OVTH , the
OVP output is pulled up to disable the PFET. When OVI is
below this threshold, the OVP output is pulled low, turning
on this PFET. In the event that large in-rush currents are
expected, it is recommended that a decoupling capacitor
be placed from OVI to GND. The body diode of this PFET
must be connected so that it is reverse biased when an
overvoltage condition exists.
A 10nF capacitor is recommended to dynamically pull-up on
the gate of Q1 if a fast edge occurs at the wall input during
a hot-plug. In the event that this capacitor is pre-charged
below the OVI rising threshold when a high voltage spike
occurs, the OVP output cannot guarantee turning off Q1
before the IN pin voltage exceeds the absolute maximum
voltage for this pin. This may occur in the event that the
wall input suddenly steps from 5.5V to a higher voltage.
In this case, a zener diode is also recommended to keep
the IN pin voltage to a safe level.
In the example of Figure 5, the input current limit from
the wall adapter is programmed to 1A with a 1k resistor
from CLPROG to GND (assuming I LIM0 and I LIM1 are held
high). And the charge current is programmed to 500mA
via the 2k resistor from the PROG pin to GND.
An optional second external PFET connected between
OUT and BAT serves as a high-performance ideal diode;
to connect the load to the battery with an extremely low
impedance. This ideal diode is controlled by the GATE
output pin whenever the wall adapter is not present or
the load demands more current than is available from
the wall adapter input (Connect the source of the PFET to
OUT and the drain to BAT).
Instantaneous monitoring of both input current and
charge current is achieved by measuring the voltages at
the CLPROG and PROG pins respectively.
Low-power shutdown is engaged by any of the following.
Disabling an external NFET tied in series with the PROG
pin resistor, by ?oating the PROG pin with a single-pole
switch, by tying R PROG to an open-drain output, by pulling
LOAD
OVI
OUT
10nF
OVP
SOURCE
10 μ F
CHRG
WALL
ADAPTER
1 μ F
10 μ F
Q1
D1
OPTIONAL
IN
GATE
LTC4067
Q2
OPTIONAL
DRAIN
NTC
BAT
1-CELL
Li-Ion
I LIM0
PROG
R PROG
2k
CHARGE CURRENT
MONITOR
INPUT
IN
I LIM1
CURRENT
MONITOR
R CLPROG
1k
CLPROG
4067 F05
GND
Q3
ENABLE
Q1, Q2: IFR7404
Figure 5. Li-Ion Charger/Controller with Overvoltage Protection
4067f
17
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4068XEDD-4.2#PBF | IC CHARGER BATT LI-ON 8-DFN |
| LTC4085EDE#PBF | IC USB POWER MANAGER 14-DFN |
| A3DDH-4418M | IDC CABLE - AKR44H/AE44M/AKR44H |
| 3-1906015-6 | CA 2.0MM OFNR 50/125,LC SEC GRN |
| RCM18DRYI | CONN EDGECARD 36POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4068-4.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-Ion Battery Charger with Programmable Termination |
| LTC4068EDD-4.2 | 功能描述:IC BATT CHARGER W/PROG TERM 8DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4068EDD-4.2#PBF | 功能描述:IC CHARGER BATT LI-ON 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4068EDD-4.2#TR | 功能描述:IC BATT CHARGER W/PROG TERM 8DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4068EDD-4.2#TRPBF | 功能描述:IC BATT CHARGER W/PROG TERM 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。