- 您现在的位置：买卖IC网 > PDF目录16307 > LTC4081EDD#PBF (Linear Technology)IC USB POWER MANAGER 10-DFN PDF资料下载
参数资料
| 型号： | LTC4081EDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC USB POWER MANAGER 10-DFN |
| 标准包装： | 121 |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 3.75 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC4081
PI FU CTIO S
BAT (Pin 1): Charge Current Output and Buck Regulator
Input. Provides charge current to the battery and regulates
the ?nal ?oat voltage to 4.2V. An internal precision resistor
divider from this pin sets the ?oat voltage and is disconnected
in charger shutdown mode. This pin must be decoupled
with a low ESR capacitor for low-noise buck operation.
V CC (Pin 2): Positive Input Supply Voltage. This pin provides
power to the battery charger. V CC can range from 3.75V
to 5.5V. This pin should be bypassed with at least a 1μF
capacitor. When V CC is less than 32mV above the BAT pin
voltage, the battery charger enters shutdown mode.
E ? N ? _ ? C ? H ? R ? G ? (Pin 3): Enable Input Pin for the Battery Charger.
Pulling this pin above the manual shutdown threshold
(V IH ) puts the LTC4081 charger in shutdown mode, thus
stopping the charge cycle. In battery charger shutdown
mode, the LTC4081 has less than 10μA supply current and
less than 5μA battery drain current provided the regula-
tor is not running. Enable is the default state, but the pin
should be tied to GND if unused.
PROG (Pin 4): Charge Current Program and Charge Cur-
rent Monitor Pin. Connecting a 1% resistor, R PROG , to
ground programs the charge current. When charging in
constant-current mode, this pin servos to 1V. In all modes,
the voltage on this pin can be used to measure the charge
current using the following formula:
pin below 0.016 ? V CC disables the NTC feature. There is
approximately 3°C of temperature hysteresis associated
with each of the input comparator’s thresholds.
? C H ? ? R ? G (Pin 6): Open-Drain Charge Status Output. The
charge status indicator pin has three states: pulldown,
high impedance state, and pulsing at 2Hz. This output can
be used as a logic interface or as an LED driver. When the
battery is being charged, the ? C ? H ? R ? G pin is pulled low by
an internal N-channel MOSFET. When the charge current
drops to 10% of the full-scale current, the ? C ? H ? R ? G pin is
forced to a high impedance state. When the battery volt-
age remains below 2.9V for one quarter of the full charge
time, the battery is considered defective, and the ? C ? H ? R ? G
pin pulses at a frequency of 2Hz with 75% duty cycle.
When the NTC pin voltage rises above 0.76 ? V CC or drops
below 0.35 ? V CC , the ? C ? H ? R ? G pin pulses at a frequency of
2Hz (25% duty cycle).
FB (Pin 7): Feedback Pin for the Buck Regulator. A resistor
divider from the regulator’s output to the FB pin programs
the output voltage. Servo value for this pin is 0.8V.
MODE (Pin 8): Burst Mode Enable Pin. Tie this pin high
to force the LTC4081 regulator into Burst Mode operation
for all load conditions. Tie this pin low to force constant-
frequency mode operation for all load conditions. Do not
?oat this pin.
I BAT =
V PROG
R PROG
? 40 0
EN_BUCK (Pin 9): Enable Input Pin for the Buck Regulator.
Pull this pin high to enable the regulator, pull low to shut
down. Do not ?oat this pin.
NTC (Pin 5): Input to the NTC (negative temperature coef-
?cient) Thermistor Temperature Monitoring Circuit. For
normal operation, connect a thermistor from the NTC pin
to ground and a resistor of equal value from the NTC pin
to V CC . When the voltage at this pin drops below 0.35 ?
V CC at hot temperatures or rises above 0.76 ? V CC at cold,
charging is suspended, the internal timer is frozen and the
SW (Pin 10): Switch Pin for the Buck Regulator. Minimize
the length of the metal trace connected to this pin. Place
the inductor as close to this pin as possible.
GND (Pin 11): Ground. This pin is the back of the Exposed
Pad package and must be soldered to the PCB for electrical
connection and rated thermal performance.
? C ? H ? R ? G pin output will start to pulse at 2Hz. Pulling this
4081f
9
相关PDF资料 |
PDF描述 |
|---|---|
| UBC1V331MNS1MS | CAP ALUM 330UF 35V 20% SMD |
| M3DRK-1606J | IDC CABLE - MKR16K/MC16G/MPR16K |
| EMM12DTKN-S288 | CONN EDGECARD 24POS .156 EXTEND |
| LTC4052EMS8E-4.2#PBF | IC CHARGER PULSE LI-ION 8-MSOP |
| EMM12DTKH-S288 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4081EDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Li-Ion Charger with NTC Input and 300mA Synchronous Buck |
| LTC4085 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Battery Charger/USB Power Manager |
| LTC4085-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB Power Manager with Ideal Diode Controller and 4.1V Li-Ion Charger |
| LTC4085-3 | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB Power Manager with Ideal Diode Controller and 3.95V Li-Ion Charger |
| LTC4085EDE | 制造商:Linear Technology 功能描述:USB Power Manager 14-Pin DFN EP |
发布紧急采购，3分钟左右您将得到回复。