- 您现在的位置：买卖IC网 > PDF目录69007 > LTC4088EDE-1#TR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 PDF资料下载
参数资料
| 型号： | LTC4088EDE-1#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| 封装： | 4 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WGED-3, DFN-14 |
| 文件页数： | 10/24页 |
| 文件大小： | 906K |
| 代理商： | LTC4088EDE-1#TR |
LTC4088-1
40881fa
charger for more current than is available will not cause
the average input current limit to be violated. It will merely
allow the battery charger to make use of all available
power to charge the battery as quickly as possible, and
with minimal power dissipation within the charger.
Alternate NTC Thermistors and Biasing
The LTC4088-1 provides temperature qualified charging if
a grounded thermistor and a bias resistor are connected
to NTC. By using a bias resistor whose value is equal to
the room temperature resistance of the thermistor (R25)
the upper and lower temperatures are pre-programmed
to approximately 40°C and 0°C, respectively (assuming
a Vishay “Curve 1” thermistor).
The upper and lower temperature thresholds can be ad-
justed by either a modification of the bias resistor value
or by adding a second adjustment resistor to the circuit.
If only the bias resistor is adjusted, then either the upper
or the lower threshold can be modified but not both. The
other trip point will be determined by the characteristics
of the thermistor. Using the bias resistor in addition to an
adjustmentresistor,boththeupperandthelowertempera-
ture trip points can be independently programmed with
the constraint that the difference between the upper and
lower temperature thresholds cannot decrease. Examples
of each technique are given below.
NTC thermistors have temperature characteristics which
areindicatedonresistance-temperatureconversiontables.
TheVishay-DalethermistorNTHS0603N011-N1003F,used
in the following examples, has a nominal value of 100k
and follows the Vishay “Curve 1” resistance-temperature
characteristic.
In the explanation below, the following notation is used.
R25 = Value of the Thermistor at 25°C
RNTC|COLD = Value of thermistor at the cold trip point
RNTC|HOT = Value of the thermistor at the hot trip
point
rCOLD = Ratio of RNTC|COLD to R25
rHOT = Ratio of RNTC|COLD to R25
RNOM=Primarythermistorbiasresistor(seeFigure2)
R1 = Optional temperature range adjustment resistor
(see Figure 3)
The trip points for the LTC4088-1’s temperature qualifica-
tion are internally programmed at 0.349 VBUS for the hot
threshold and 0.765 VBUS for the cold threshold.
Therefore, the hot trip point is set when:
R
V
NTcHOT
NOM
NTcHOT
BUS
|
.
+
= 0 349
and the cold trip point is set when:
R
V
NTccOLD
NOM
NTccOLD
BUS
|
.
+
= 0 765
Solving these equations for RNTC|COLD and RNTC|HOT
results in the following:
RNTC|HOT = 0.536 RNOM
and
RNTC|COLD = 3.25 RNOM
By setting RNOM equal to R25, the above equations result
in rHOT = 0.536 and rCOLD = 3.25. Referencing these ratios
to the Vishay Resistance-Temperature Curve 1 chart gives
a hot trip point of about 40°C and a cold trip point of about
0°C. The difference between the hot and cold trip points
is approximately 40°C.
By using a bias resistor, RNOM,differentinvaluefromR25,
the hot and cold trip points can be moved in either direc-
tion. The temperature span will change somewhat due to
the non-linear behavior of the thermistor. The following
equations can be used to easily calculate a new value for
the bias resistor:
R
r
R
r
R
NOM
HOT
NOM
cOLD
=
0 536
25
3 25
25
.
.
where rHOT and rCOLD are the resistance ratios at the
desired hot and cold trip points. Note that these equations
are linked. Therefore, only one of the two trip points can
be chosen, the other is determined by the default ratios
APPLICATIO S I FOR ATIO
W
U
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4088EDE | 3 A BATTERY CHARGE CONTROLLER, 2.7 kHz SWITCHING FREQ-MAX, PDSO14 |
| LTC4096EDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4269CDKD-2#TR | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4269IDKD-2 | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4269CDKD-2 | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4088EDE-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage |
| LTC4088EDE-2#PBF | 功能描述:IC CHRGR BATT HE 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4088EDE-2#TRPBF | 功能描述:IC CHRGR BATT HE 14-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4088EDE-2-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage |
| LTC4088EDE-2-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency Battery Charger/USB Power Manager with Regulated Output Voltage |
发布紧急采购，3分钟左右您将得到回复。