- 您现在的位置：买卖IC网 > PDF目录67759 > LTC4098EUDC-3.6#PBF (LINEAR TECHNOLOGY CORP) BATTERY CHARGE CONTROLLER, PQCC20 PDF资料下载
参数资料
| 型号： | LTC4098EUDC-3.6#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | BATTERY CHARGE CONTROLLER, PQCC20 |
| 封装： | 3 X 4 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-20 |
| 文件页数： | 9/32页 |
| 文件大小： | 1915K |
| 代理商： | LTC4098EUDC-3.6#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4098-3.6
409836f
transistormaybeaddedfromBATtoVOUT.TheIDGATEpin
of the LTC4098-3.6 drives the gate of the external P-chan-
nel MOSFET transistor for automatic ideal diode control.
The source of the external P-channel MOSFET should be
connected to VOUT and the drain should be connected to
BAT. Capable of driving a 1nF load, the IDGATE pin can
control an external P-channel MOSFET transistor having
an on-resistance of 30m
Ω or lower. Figure 5 shows the
decreased forward voltage compared to a conventional
Schottky diode.
Suspend LDO
TheLTC4098-3.6providesasmallamountofpowertoVOUT
in suspend mode by including an LDO from VBUS to VOUT.
This LDO will prevent the battery from running down when
the portable product has access to a suspended USB port.
Regulating at 3.8V, this LDO only becomes active when the
switching converter is disabled. In accordance with the
USBspecification,theinputtotheLDOiscurrentlimitedso
thatitwillnotexceedthelowpowerorhighpowersuspend
specification. If the load on VOUTexceedsthesuspendcur-
rent limit, the additional current will come from the battery
via the ideal diodes. The suspend LDO sends a scaled copy
of the VBUS current to the CLPROG pin, which will servo to
approximately 100mV in this mode. Thus, the high power
and low power suspend settings are related to the levels
programmed by the same resistor for 1x and 5x modes.
Battery Charger
The LTC4098-3.6 includes a constant-current/constant-
voltagebatterychargerwithautomaticrecharge,automatic
termination by safety timer and thermistor sensor input
for out-of-temperature charge pausing.
The charger begins charging in full power constant-cur-
rent mode. The current delivered to the battery will try to
reach 1030V/RPROG. Depending on available input power
and external load conditions, the battery charger may or
may not be able to charge at the full programmed rate.
The external load will always be prioritized over the bat-
tery charge current. The USB current limit programming
will always be observed and only additional power will be
available to charge the battery. When system loads are
light, battery charge current will be maximized.
Charge Termination
The battery charger has a built-in safety timer. Once the
voltage on the battery reaches the preprogrammed float
voltageof3.600V,thechargerwillregulatethebatteryvolt-
age there and the charge current will decrease naturally.
Once the charger detects that the battery has reached
3.600V, the 1-hour safety timer is started. After the safety
timer expires, charging of the battery will discontinue and
no more current will be delivered.
Automatic Recharge
Once the battery charger terminates, it will remain off
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that
the battery is always topped off, a charge cycle will au-
tomatically begin when the battery voltage falls below
VRECHRG (typically 3.5V). In the event that the safety timer
is running when the battery voltage falls below VRECHRG, it
will reset back to zero. To prevent brief excursions below
VRECHRGfromresettingthesafetytimer,thebatteryvoltage
must be below VRECHRG for more than 1.5ms. The charge
cycle and safety timer will also restart if the VBUS UVLO
cycles low and then high (e.g., VBUS is removed and then
replaced) or if the charger is momentarily disabled using
the D2 pin.
Charge Current
The charge current is programmed using a single resistor
from PROG to ground. 1/1030th of the battery charge cur-
rent is delivered to PROG, which will attempt to servo to
1.000V. Thus, the battery charge current will try to reach
1030 times the current in the PROG pin. The program
resistor and the charge current are calculated using the
following equations:
R
V
I
V
R
PROG
cHG
PROG
=
1030
,
In either the constant-current or constant-voltage charg-
ing modes, the voltage at the PROG pin will be propor-
tional to the actual charge current delivered to the
battery. The charge current can be determined at any time
operaTion
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4210-4IS6 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4210-3IS6 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4210-4CS6 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4355CMS#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4355CMS#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4099 | 制造商:LINER 制造商全称:Linear Technology 功能描述:I2C Controlled USB Power Manager/Charger with Overvoltage Protection |
| LTC4099EPDC#PBF | 功能描述:IC USB PWR MANAGER/CHRGR 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC4099EPDC#TRMPBF | 制造商:Linear Technology 功能描述: |
| LTC4099EPDC#TRPBF | 功能描述:IC USB PWR MANAGER/CHRGR 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC4099EPDC-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:I2C Controlled USB Power Manager/Charger with Overvoltage Protection |
发布紧急采购，3分钟左右您将得到回复。