参数资料
| 型号： | LTC4213IDDB#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | IC CIRC BREAK ELEC 8-DFN |
| 标准包装： | 2,500 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN（3x2） |
| 包装： | 带卷 (TR) |
LTC4213
7
4213f
PI FU CTIO S
UU
U
READY (Pin 1): READY Status Output. Open drain output
that goes high impedance when the external MOSFET is on
and the circuit breaker is armed. Otherwise this pin pulls
low.
ON (Pin 2): ON Control Input. The LTC4213 is in reset
mode when the ON pin is below 0.4V. When the ON pin
increases above 0.8V, the device starts up and the GATE
pulls up with a 100A current source. When the ON pin
drops below 0.76V, the GATE pulls down. To reset a circuit
breaker fault, the ON pin must go below 0.4V.
ISEL (Pin 3): Threshold Select Input. With the ISEL pin
grounded, float or tied to VCC the VCB is set to 25mV, 50mV
or 100mV, respectively. The corresponding VCB(FAST)
values are 100mV, 175mV and 325mV.
GND (Pin 4): Device Ground.
GATE (Pin 5): GATE Drive Output. An internal charge
pump supplies 100A pull-up current to the gate of the
external N-channel MOSFET. Internal circuitry limits the
voltage between the GATE and SENSEN pins to a safe gate
drive voltage of less than 8V. When the circuit breaker
trips, the GATE pin abruptly pulls to GND.
SENSEN (Pin 6): Circuit Breaker Negative Sense Input.
Connect this pin to the source of the external MOSFET.
During reset or fault mode, the SENSEN pin discharges the
output to ground with 280A.
SENSEP (Pin 7): Circuit Breaker Positive Sense Input.
Connect this pin to the drain of external N-channel MOSFET.
The circuit breaker trips when the voltage across SENSEP
and SENSEN exceeds VCB. The input common mode range
of the circuit breaker is from ground to VCC + 0.2V when
VCC < 2.5V. For VCC ≥ 2.5V, the input common mode range
is from ground to VCC + 0.4V.
VCC (Pin 8): Bias Supply Voltage Input. Normal operation
is between 2.3V and 6V. An internal under-voltage lockout
circuit disables the device when VCC < 2.07V.
Exposed Pad (Pin 9): Exposed pad may be left open or
connected to device ground.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4258CGW#TRPBF | IC POE 802.3AF QUAD 36-SSOP |
| LTC4259ACGW#TR | IC CTRLR POE QUAD AC DISC 36SSOP |
| LTC4264IDE#TRPBF | IC CNTRLR PD INTERFACE 12-DFN |
| LTC4266IGW#PBF | IC CTRLR IEEE 802.3AT 36-SSOP |
| LTC4267IDHC#TRPBF | IC POE 802.3AF INTERFACE 16-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4214 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Hot Swap Controller |
| LTC4214-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative Low Voltage Hot Swap Controllers |
| LTC4214-1CMS | 功能描述:IC CTRLR HOTSWAP NEGVOLT 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4214-1CMS#PBF | 功能描述:IC CTRLR HOTSWAP NEGVOLT 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4214-1CMS#TR | 功能描述:IC CTRLR HOTSWAP NEG LV 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。