- 您现在的位置：买卖IC网 > Datasheet目录42 > LTC4230CGN#TRPBF (Linear Technology)IC CONTRLLR HOT SWAP TRPL 20SSOP Datasheet资料下载
参数资料
| 型号： | LTC4230CGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/36页 |
| 文件大小： | 384K |
| 描述： | IC CONTRLLR HOT SWAP TRPL 20SSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 1.7 V ~ 16.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
8
LTC4230
4230f
FB3 (Pin 1): The FB3 (Feedback) pin is an input to the
FBCOMP3 comparator which monitors the V
CC3
output
supply voltage through an external resistor divider. If V
FB3
< 1.234V, RESET 3 pin pulls low. An internal glitch filter at
FBCOMP3s output prevents triggering a reset condition
due to negative voltage transients. If V
FB3
> 1.237V,
RESET 3 pin goes high after exiting undervoltage lockout.
RESET 3 (Pin 2): An open-drain N-channel device whose
source connects to GND (Pin 14). This pin pulls low if the
voltage at FB3 (Pin 1) falls below the FB3 threshold
(1.234V). This pin requires an external pull-up resistor to
V
OUT3
. If an undervoltage lockout condition occurs,
RESET 3 pulls low independently of FB3 to prevent false
glitches.
GATE 3 (Pin 3): The output signal at this pin is the high side
gate drive for Channel 3s external N-channel MOSFET
pass transistor. An internal charge pump produces a 4.5V
(minimum) to 18V (maximum) gate drive voltage for V
CC1
supply voltages from 2.7V to 16.5V, respectively.
As shown in the Block Diagram for each channel, an
internal charge pump supplies a 10礎 gate current and
sufficient gate voltage drive to the external MOSFET. The
internal charge pump produces a minimum 4.5V gate
drive for V
CC1
< 4.75V. For V
CC1
> 4.75V, the minimum
gate voltage drive is 9V. For V
CC1
e 12V, the minimum gate
voltage drive is 7V which is set by an internal zener diode
clamp connected between the GATE 3 pin and GND.
SENSE 3 (Pin 4): Circuit Breaker Sense Pin for Channel 3.
With a sense resistor placed in the power path between
V
CC3
and SENSE 3, Channel 3s electronic circuit breaker
trips if the voltage across the sense resistor (V
CC3
V
SENSE3
) exceeds the thresholds set internally for SLOW
COMP3 and FAST COMP3, as shown in the Block Diagram.
The threshold for SLOW COMP3 is V
CB(SLOW)
= 50mV, and
the electronic circuit breaker trips if the voltage across
R
SENSE3
exceeds 50mV for 10祍, or for the time delay
programmed by C
FILTER
. To adjust SLOW COMP3s delay,
please refer to the section on Adjusting SLOW COMPns
Response Time.
Under transient conditions where large step current
changes can and do occur over shorter periods of time, a
PI FU CTIO S
U
U
second (fast) comparator instead trips the electronic
circuit breaker. The threshold for FAST COMP3 is set at
V
CB(FAST)
= 150mV, and the circuit breaker trips if the
voltage across the R
SENSE3
exceeds 150mV for more than
500ns. FAST COMP3s delay is fixed in the LTC4230 and
cannot be adjusted. To disable Channel 3s electronic
circuit breaker, connect the V
CC3
and SENSE 3 pins
together.
V
CC3
(Pin 5): Positive Supply Input for Channel 3. V
CC3
operates from 1.7V to 15.5V (V
CC3
d V
CC1
1V) and its
supply current, I
CC3
, is typically 65礎. The master UVLO
circuit disables all three GATEn outputs of the LTC4230
until the voltage at V
CC3
exceeds 1.19V.
V
CC1
(Pin 6): This is the positive supply input to the
LTC4230, the power supply input for Channel 1, and the
power supply input for all three internal charge pumps.
The LTC4230 operates from 2.7V to 16.5V, and the I
CC1
supply current is typically 1.8mA. The master UVLO circuit
disables all three GATEn outputs of the LTC4230 if V
CC1
is
less than 2.35V. The internal charge pump outputs are
enabled when V
CC1
> 2.35V, V
CC2
> 2.15V, and
V
CC3
> 1.19V.
SENSE 1 (Pin 7): Circuit Breaker Sense Pin for Channel 1.
With a sense resistor placed in the power path between
V
CC1
and SENSE 1, Channel 1s electronic circuit breaker
trips if the voltage across the sense resistor (V
CC1
V
SENSE1
) exceeds the thresholds set internally for SLOW
COMP1 and FAST COMP1, as shown in the Block Diagram.
The threshold for SLOW COMP1 is V
CB(SLOW)
= 50mV, and
the electronic circuit breaker trips if the voltage across
R
SENSE1
exceeds 50mV for 10祍, or for the time delay
programmed by C
FILTER
. To adjust SLOW COMP1s delay,
please refer to the section on Adjusting SLOW COMPns
Response Time.
Under transient conditions where large step current changes
can and do occur over shorter periods of time, a second
(fast) comparator instead trips the electronic circuit breaker.
The threshold for FAST COMP1 is set at V
CB(FAST)
= 150mV,
and the circuit breaker trips if the voltage across the
R
SENSE1
exceeds 150mV for more than 500ns. FAST
COMP1s delay is fixed in the LTC4230 and cannot be
adjusted. To disable Channel 1s electronic circuit breaker,
connect the V
CC1
and SENSE 1 pins together.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4232CDHC#TRPBF | IC CTLR HOT SWAP 5A 16-DFN |
| LTC4240IGN#TRPBF | IC CTRLR HOTSWAP CPCI I2C 28SSOP |
| LTC4241IGN#PBF | IC CTRLR HOTSWAP 3.3V AUX 20SSOP |
| LTC4242CUHF#TRPBF | IC CNTRLR HOT SWAP 38-QFN |
| LTC4244CGN-1#TRPBF | IC CTRLR HOTSWAP PCI 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4230IGN | 功能描述:IC CONTRLLR HOT SWAP TRPL 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4230IGN#PBF | 功能描述:IC CONTRLLR HOT SWAP TRPL 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4230IGN#TR | 功能描述:IC CONTRLLR HOT SWAP TRPL 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4230IGN#TRPBF | 功能描述:IC CONTRLLR HOT SWAP TRPL 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4232CDHC#PBF | 功能描述:IC CTLR HOT SWAP 5A 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。