- 您现在的位置：买卖IC网 > PDF目录19738 > LTC4241IGN#TRPBF (Linear Technology)IC CTRLR HOTSWAP 3.3V AUX 20SSOP PDF资料下载
参数资料
| 型号： | LTC4241IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 279K |
| 描述： | IC CTRLR HOTSWAP 3.3V AUX 20SSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | PCI，PCI-X |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，±12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
LTC4241
7
sn4241 4241f
12V
IN
(Pin 1): 12V Supply Input. This pin powers the
primary controller internal circuitry. A 0.5& switch is
connected between 12V
IN
and 12V
OUT
with a foldback
current limit. An undervoltage lockout circuit prevents the
switches from turning on while the 12V
IN
pin voltage is
less than 9V.
V
EEIN
(Pin 2): 12V Supply Input. A 1.2& switch is
connected between V
EEIN
and V
EEOUT
with a foldback
current limit.
3V
OUT
(Pin 3): 3.3V Output Monitor. Used to monitor the
3.3V output supply voltage. The PWRGD signal cannot go
low until the 3V
OUT
pin exceeds 2.9V.
TIMER (Pin 4): Current Limit Fault Timer Input. Connect a
capacitor from TIMER to ground. With the primary con-
troller turned off (ON = GND) or the internal circuit breaker
tripped due to a PCI supply fault (FAULT = low), the TIMER
pin is internally held at ground. When the primary control-
ler is turned on, a 22礎 pull-up current source is con-
nected to TIMER. Current limit faults from the PCI supplies
will be ignored until the voltage at the TIMER pin rises to
within 0.9V of 12V
IN
.
ON (Pin 5): On Control Input. A rising edge turns on the
external N-channel FETs for 3.3V and 5V PCI supplies, the
internal 12V and 12V switches and a falling edge turns it
off. If the ON pin is cycled low then high following the trip
of the circuit breaker due to a PCI supply fault, the circuit
breaker is reset.
FAULT (Pin 6): Fault Output. Open drain logic output used
by both the primary and auxiliary controller to indicate an
overcurrent fault condition. When any of the PCI and 3.3V
auxiliary supplies are in current limit fault, the controller
detecting the fault (primary or auxiliary) will be latched off
and the FAULT pin will be pulled low. Current limit faults
from the PCI supplies are ignored while the voltage at the
TIMER pin is less than (12V
IN
0.9V). The current limit
fault detected by the primary controller will not cause the
auxiliary controller to latch off and vice versa.
PWRGD (Pin 7): Power Good Output. Open drain logic
output used by the primary controller to indicate the
voltage status of the PCI supplies. PWRGD remains low
while V
12VOUT
e 11.1V, V
3VOUT
e 2.9V, V
5VOUT
e 4.65V,
V
VEEOUT
d 10.5V. When one of the supplies falls below its
U
U
PI FU CTIO S
power good threshold voltage, PWRGD will go high after
a 15祍 deglitching time. The switches will not be turned off
when PWRGD goes high.
GND (Pin 8): Chip Ground
AUXGATE (Pin 9): High Side Gate Drive for the 3.3V
Auxiliary External N-channel MOSFET. An internal charge
pump generates at least 8V of gate drive from a 3.3V
auxiliary supply. A zener clamps AUXGATE approximately
12V above the supply voltage at AUXIN. The rise time at
AUXGATE is set by an external AUXGATE capacitor con-
nected to ground and an internal 10礎 current source
provided by the charge pump. If the circuit breaker trips or
the auxiliary supply voltage hits the undervoltage lockout
threshold, a 50mA current sink rapidly pulls AUXGATE
low.
AUXSENSE (Pin 10): 3.3V Auxiliary Circuit Breaker Cur-
rent Sense Input. The load current is monitored by a sense
resistor connected between AUXIN and AUXSENSE. The
circuit breaker trips if the voltage across the sense resistor
exceeds 50mV and the AUXGATE pin voltage will be turned
off.
AUXIN (Pin 11): 3.3V Auxiliary Supply Input. This pin
powers the auxiliary controller internal circuitry. An
undervoltage lockout circuit disables the AUXGATE pin
until the supply voltage at AUXIN is greater than 2.6V.
AUXGATE is held at ground potential until the undervoltage
lockout deactivates. If no 3.3V auxiliary supply is available,
tie AUXIN to ground.
AUXON (Pin 12): ON Control Input for Auxiliary Supply. A
rising edge turns on the external N-channel FET for 3.3V
auxiliary supply and a falling edge turns it off. If the AUXON
pin is cycled low then high following the trip of the circuit
breaker due to a 3.3V auxiliary supply fault, the circuit
breaker is reset.
3V
IN
(Pin 13): 3.3V Supply Sense Input. An undervoltage
lockout circuit prevents the switches from turning on
when the voltage at the 3V
IN
pin is less than 2.5V. If no 3.3V
input supply is available, tie 3V
IN
to the 5V
IN
pin.
3V
SENSE
(Pin 14): 3.3V Current Limit Set Pin. With a sense
resistor placed in the supply path between 3V
IN
and
3V
SENSE
, the GATE pin voltage will be adjusted to maintain
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2954-02BZ TR | IC REG LDO 5V .25A TO92-3 |
| MIC2954-02BT | IC REG LDO 5V .25A TO220-3 |
| CDRH104RNP-470NC | INDUCTOR POWER 47UH 2.10A SMD |
| MIC2954-02BS TR | IC REG LDO 5V .25A SOT-223 |
| TNY266GN | IC OFFLINE SWIT OTP OCP HV 8SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4242 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
| LTC4242CG | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
| LTC4242CG#PBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4242CG#TRPBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4242CUHF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Slot Hot Swap Controller for PCI Express |
发布紧急采购，3分钟左右您将得到回复。