- 您现在的位置：买卖IC网 > PDF目录179919 > LTC4259ACGW#TRPBF (LINEAR TECHNOLOGY CORP) Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C PDF资料下载
参数资料
| 型号： | LTC4259ACGW#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封装： | 0.300 INCH, LEAD FREE, PLASTIC, SSOP-36 |
| 文件页数： | 16/32页 |
| 文件大小： | 409K |
| 代理商： | LTC4259ACGW#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4259A
23
4259afb
OSCIN Input and Oscillator Requirements
AC disconnect depends on an external oscillator source
applied to the OSCIN pin. The LTC4259A measures port
impedance by applying an amplified version of the OSCIN
signal to the port’s DETECT pin (see Figure 18). The
oscillator should be well-controlled because errors in this
signal become errors in the measured port impedance. As
shown in Figure 19, the load being sensed by AC discon-
nect has a resistive and a large reactive component.
Current through the PD’s signature resistor depends on
the amplitude of the AC signal while current into the
capacitors depends on the slew rated: I = C dV/dt.
Consequently, the LTC4259A is sensitive to the amplitude
and slew rate of the OSCIN signal, but is more tolerant of
frequency and offset errors. Internal limits prevent the
LTC4259A from being adversely affected by OSCIN sig-
nals with excessive amplitude.
There are many ways to build oscillators with controlled
amplitudes and slew rates, especially since the frequency
of the oscillator does not have to be well-controlled.
Contact the LTC Applications department for oscillator
circuits.
As alluded to previously, AC disconnect is complicated
and redesigning for different component sizes is a difficult
task. For optimum performance, use the recommended
component values and drive OSCIN with a 100Hz 2VP-P,
1.2V offset sine wave. Keep in mind that the IEEE 802.3af
specification places upper limits of 100V/ms on the slew
rate and 500Hz on the frequency of the AC signal at the
port. Voltage gain, AVACD, from OSCIN to DETECTn in-
creases the slew rate by the voltage gain. Since AVACD has
a maximum absolute value of 3.3V/V (
±3V typ), the slew
rate at the OSCIN pin must be less than 30V/ms. A slew
rate around 0.6V/ms at OSCIN will work with the recom-
mended values of CDET, RDET and CPSE.
The LTC4259A’s OSCIN input amplifier will accept signals
between DGND – 0.3V and VDD + 0.5V. This amplifier has
a gain of –1 and is referenced to 1.2V above DGND. An
OSCIN voltage greater than 2.2V will cause the amplifier’s
output to clip against DGND. Clipping will not affect the
performance of AC disconnect until the clipping becomes
so severe that even the midrange (where the controlled
slew rate occurs) of the signal is clipped. Keep the midrange
or average voltage of the OSCIN signal between 0.9V and
1.5V to avoid severe clipping. OSCIN signals below DGND
can interact with the ESD protection circuitry on the pin
and are not recommended. Also, meeting the IEEE 802.3af
specification for maximum AC amplitude on the port just
after the PD is removed depends on the OSCIN input peak-
to-peak amplitude. Clipping by LTC4259A’s OSCIN input
circuitry will generally ensure that this specification is not
exceeded. Note that under normal operation, the AC dis-
connect output on the DETECT
n pin will have an amplitude
near 6V peak-to-peak. The combination of RDET, CDET and
CPSE attenuate the signal so roughly half this amplitude is
seen at the port when the port is powered and the PD has
just been removed. When the PD is still connected there
will be almost no AC signal at the port.
The LTC4259A monitors Pin 36 for the presence of an
oscillating signal. If no signal is present and the Osc Fail
Mask bit is set, then Osc Fail (bit 1 of the Supply Event
register) is set, triggering an interrupt. As the LTC4259A’s
AC disconnect circuitry self-checks the OSCIN signal, the
Osc Fail bit is intended as a fault indicator to alert the PSE
host controller. The Osc Fail bit has no effect beyond
triggering the interrupt. A clear Osc Fail bit indicates that
the OSCIN signal goes below 0.6V and above 1.8V at least
once every 250ms. It does not necessarily guarantee that
AC disconnect will function properly. However, AC discon-
nect itself is a more thorough test of the OSCIN signal.
When the OSCIN signal is either absent or corrupted,
powered ports with AC disconnect enabled (and DC dis-
connect not enabled) will automatically disconnect. After
the LTC4259A is reset (by power on, Reset All bit or the
RESET pin) the Osc Fail bit is set. Once the Osc Fail bit is
cleared, it will only be set by an invalid signal on the OSCIN
pin or another reset.
SERIAL DIGITAL INTERFACE
The LTC4259A communicates with a host (master) using
the standard 2-wire interface as described in the SMBus
Specification Version 2.0 (available at http://smbus.org).
The SMBus is an extension of the I2C bus, and the
LTC4259A is also compatible with the I2C bus standard.
The Timing Diagrams (Figures 6 through 10) show the
timing relationship of the signals on the bus. The two bus
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4261CUFD#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261CUFD-2#PBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261CUFD-2#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261IGN#PBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: SSOP; No of Pins: 28; Temperature Range: -40°C to +85°C |
| LTC4261IGN#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: SSOP; No of Pins: 28; Temperature Range: -40°C to +85°C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4259AIGW-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect |
| LTC4259AIGW-1#PBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259AIGW-1#TRPBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全称:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
发布紧急采购，3分钟左右您将得到回复。