- 您现在的位置：买卖IC网 > PDF目录179919 > LTC4259ACGW#TRPBF (LINEAR TECHNOLOGY CORP) Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C PDF资料下载
参数资料
| 型号： | LTC4259ACGW#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect; Package: SSOP; No of Pins: 36; Temperature Range: 0°C to +70°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封装： | 0.300 INCH, LEAD FREE, PLASTIC, SSOP-36 |
| 文件页数： | 5/32页 |
| 文件大小： | 409K |
| 代理商： | LTC4259ACGW#TRPBF |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4259A
13
4259afb
involves reading the register to determine its status, set-
ting the appropriate bit in software and writing back the
entire register, a pushbutton register allows a single bit to
be written without knowing or affecting the status of the
other bits in the register. Pushbutton registers are write-
only and will return 00h if read.
Det/Class Restart PB (Address 18h): Detection/Classifi-
cation Restart Pushbutton Register, Write Only. Writing a
1 to any bit in this register will start or restart a single
detection or classification cycle at the corresponding port
in Manual mode. It can also be used to set the correspond-
ing bits in the Detect/Class Enable register (address 14h)
for ports in auto or semiauto mode. The lower 4 bits affect
detection on each port while the upper 4 bits affect
classification.
Power Enable PB (Address 19h): Power Enable Pushbutton
Register, Write Only. The lower four bits of this register set
the Power Enable bit in the corresponding Port Status reg-
ister; the upper four bits clear the corresponding Power
Enable bit. Setting or clearing the Power Enable bits via this
register will turn on or off the power in any mode except
shutdown, regardless of the state of detection or classifi-
cation. Note that tICUT, tSTART and disconnect events (if
enabled) will still turn off power if they occur.
The Power Enable bit cannot be set if the port has turned
off due to a tICUT or tSTART fault and the tICUT timer has not
yet counted back to zero. See Applications Information for
more information on tICUT timing.
Clearing the Power Enable bits with this register also
clears the detect and fault event bits, the Port Status
register, and the Detection and Classification Enable bits
for the affected port(s).
Reset PB (Address 1Ah): Reset Pushbutton, Write Only.
Bits 0-3 reset the corresponding port by clearing the power
enable bit, the detect and fault event bits, the status regis-
ter and the detection and classification enable bits for that
port. Bit 4 returns the entire LTC4259A to the power-on
reset state; all ports are turned off, the AUTO pin is reread
and all registers are returned to their power-on defaults,
except VDDUVLO, which remains cleared. Bit 5 is reserved;
setting it has no effect. Setting bit 6 releases the Interrupt
pin if it is asserted without affecting the Event registers or
the Interrupt register. When the INT pin is released in this
Detect/Class Enable (Address 14h): Detection and Clas-
sification Enable, Read/Write. The lower four bits of this reg-
ister enable the detection circuitry at the corresponding port
if that port is in Auto or Semiauto mode. The upper four bits
enable the classification circuitry at the corresponding port
if that port is in Auto or Semiauto mode. In manual mode,
setting a bit in this register will cause the LTC4259A to per-
form one classification or detection cycle on the corre-
sponding port. Writing to the Detect/Class Restart PB (18h)
has the same effect without disturbing the Detect/Class
Enable bits for other ports.
Timing Config (Address 16h):Global Timing Configuration,
Read/Write. Bits 0-1 program tDIS, the time duration before
a port is automatically tuned off after the PD is removed.
The LTC4259A can be programmed to monitor whether port
current is below IMIN (DCconnect)orportimpedanceishigh
(AC disconnect). Bits 2-3 program tICUT, the time during
which a port’s current can exceed ICUT without it being
turned off. If the current is still above ICUT after tICUT, the
LTC4259A will indicate a tICUT fault and turn the port off.
Bits 4-5 program tSTART, the time duration before an over-
current condition during port power-on is considered a
tSTART fault and the port is turned off. Note that using the
tICUT and tSTART times other than the default is not compli-
ant with IEEE 802.3af and may double or quadruple the
energy dissipated by the external MOSFETs during fault con-
ditions. Bits 6-7 are reserved and should be read/written
as 0. See Electrical Characteristics for timer bit encoding.
Also see the Applications Information for descriptions of
tSTART, tICUT, DC and AC disconnect timing.
Misc Config (Address 17h): Miscellaneous Configuration,
Read/Write. Bit 5 is the Osc Fail Mask; it is set by default.
When the Osc Fail Mask bit is clear, it prevents a failure on
the OSCIN pin from setting the Osc Fail bit and causing a
Supply Event Interrupt. Setting bit 7 enables the INT pin.
If this bit is reset, the LTC4259A will not pull down the INT
pin in any condition nor will it respond to the Alert Response
Address. This bit is set by default.
Pushbutton Registers
Note Regarding Pushbutton Registers: “Pushbutton” reg-
isters are specialized registers that trigger an event when
a 1 is written to a bit; writing a 0 to a bit will do nothing. Unlike
a standard read/write register, where setting a single bit
REGISTER FU CTIO S
U
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4261CUFD#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261CUFD-2#PBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261CUFD-2#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: QFN; No of Pins: 24; Temperature Range: 0°C to +70°C |
| LTC4261IGN#PBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: SSOP; No of Pins: 28; Temperature Range: -40°C to +85°C |
| LTC4261IGN#TRPBF | Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring; Package: SSOP; No of Pins: 28; Temperature Range: -40°C to +85°C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4259AIGW-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect |
| LTC4259AIGW-1#PBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259AIGW-1#TRPBF | 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全称:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
发布紧急采购，3分钟左右您将得到回复。