- 您现在的位置：买卖IC网 > PDF目录19914 > LTC4308CDD#PBF (Linear Technology)IC BUS BUFFER LV 8-DFN PDF资料下载
参数资料
| 型号： | LTC4308CDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 168K |
| 描述： | IC BUS BUFFER LV 8-DFN |
| 产品培训模块： | LTC4310 - Hot-Swappable I²C Isolators |
| 标准包装： | 121 |
| 类型： | 热交换开关 |
| 应用： | 通用型缓冲器/总线扩展器 |
| 内部开关： | 是 |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 管件 |
LTC4308
10
4308f
When powering up into a bus stuck low condition, the
connection circuitry connecting the SDA and SCL pins are
not activated. 30ms after UVLO, automatic clocking and
stop bit generation takes place as described above.
READY Digital Output
This pin provides a digital ag which is low when either
ENABLE is low, the start-up sequence described earlier
in this section has not been completed, or the LTC4308
has disconnected the input and output busses due to a
bus stuck low condition. READY goes high when ENABLE
is high and start-up is complete. The pin is driven by an
open-drain pull-down device capable of sinking 3mA while
holding 0.4V on the pin. Connect a resistor to the bus
pull-up supply to provide the pull-up.
ENABLE
When the ENABLE pin is driven below 0.45V with respect
to the LTC4308s ground, the input pin is disconnected
from the output pin and the READY pin is pulled low.
When the pin is driven above 0.75V , the part waits for
data transactions on both the input and output pins to be
complete (as described in the Start-Up section) before
connecting the two pins. At this time the internal pull-down
on READY releases.
A rising edge on ENABLE after a bus stuck low condition
has occurred forces a connection between SDAIN, SDAOUT ,
and SCLIN, SCLOUT even if the bus stuck low condition
has not been cleared. At this time the 30ms timer is reset,
but not disabled.
Rise Time Accelerators
Once connection has been established, rise time accelera-
tor circuits on SDAOUT and SCLOUT are enabled. During
positive bus transitions of at least 0.8V/約, the rise time
accelerators provide strong, slew-limited pull-up currents
to force the bus voltage to rise at a rate of 100V/約.
The rise time accelerators signi cantly improve reli-
ability and performance in I
2
C systems in several ways.
First, due to the accelerators signi cantly lower pull-up
impedance, as compared to the bus pull-up resistance,
the system is less susceptible to noise on rising edges,
providing smooth, controlled transitions for both small
and large systems. Second, the accelerators allow users
to choose larger bus pull-up resistors, reducing power
consumption and improving logic low noise margins or
to design with bus capacitances beyond those speci ed
in the I
2
C speci cations.
For these reasons, it is strongly recommended that users
choose bus pull-up resistors that guarantee the output
busses will rise on their own at a rate of at least 0.8 V/約 to
ensure activation of the accelerators. See the Applications
Information section for selecting pull-up resistor sizes.
It is important to connect SDAOUT and SCLOUT pins to
a bus whose pull-up supply is equal to or greater than
the LTC4308s supply to ensure the accelerators do not
source current through the pull up resistors into the pull-
up supply.
The rise time accelerators are internally disabled until the
sequence of events described in the start-up section has
been completed, as well as during automatic clocking and
stop bit generation for a bus stuck low recovery event.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JNL-CY-B1 | CONVERTER MOD DC/DC 28V 50W |
| HSM36DSEH | CONN EDGECARD 72POS .156 EYELET |
| AT18F002-30XU | IC FLASH CONFIG 2MBIT 20-TSSOP |
| LTC4307CDD-1#PBF | IC BUFFER 2-WIRE BUS 8-DFN |
| LTC4216IMS#PBF | IC CNTRLR HOT SWAP 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4308CMS8#PBF | 功能描述:IC BUS BUFFER LV 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4308CMS8#PBF | 制造商:Linear Technology 功能描述:IC HOT SWAP BUS BUFFER MSOP-8 |
| LTC4308CMS8#TRPBF | 功能描述:IC BUS BUFFER LV 8-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4308IDD#PBF | 功能描述:IC BUS BUFFER LV 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4308IDD#TRPBF | 功能描述:IC BUS BUFFER LV 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。